A5062801799- Cellular and Composite Structures
- Composite Structure Analysis and Optimization
- Nonlocal and gradient elasticity in micro/nano structures
- Transportation Safety and Impact Analysis
- Material Properties and Processing
- Vibration and Dynamic Analysis
- Mechanical Behavior of Composites
- Advanced Welding Techniques Analysis
- Aluminum Alloys Composites Properties
- Structural Analysis and Optimization
- Acoustic Wave Phenomena Research
- Fluid Dynamics Simulations and Interactions
- Automotive and Human Injury Biomechanics
- Numerical methods in engineering
- Structural Behavior of Reinforced Concrete
- Mechanical stress and fatigue analysis
- Structural Response to Dynamic Loads
- Tribology and Wear Analysis
- Carbon Nanotubes in Composites
- Advanced machining processes and optimization
- Advanced Machining and Optimization Techniques
- Advanced MEMS and NEMS Technologies
- Vibration Control and Rheological Fluids
- Geotechnical Engineering and Underground Structures
- Metal Forming Simulation Techniques
Politecnico di Milano
2019-2022
Shenyang University of Technology
2022
Jianghan University
2022
Qatar University
2013-2021
Duy Tan University
2020-2021
Qingdao University of Technology
2021
American University of Sharjah
2021
Qingdao University of Science and Technology
2021
South Ural State University
2021
CMR University
2020
Friction-based welding processes are considered as very efficient solid-state metal joining due to soundness of the welded joint with remarkably less energy consumption and environmentally friendly. The terminology behind these is make use elevated temperatures caused by mechanical friction at contacting surfaces fuse materials together. Several different friction-based techniques classified briefly explaining their mechanisms show a comparison between (FRW) stir (FSW). In FRW contact...
Natural fiber composites (NFCs) are an evolving area in polymer sciences. Fibers extracted from natural sources hold a wide set of advantages such as negligible cost, significant mechanical characteristics, low density, high strength-to-weight ratio, environmental friendliness, recyclability, etc. Luffa cylindrica, also termed luffa gourd or sponge, is that has solid potential to replace synthetic fibers composite materials diverse applications like vibration isolation, sound absorption,...
The volume of fluid (VOF) modeling method was implemented to simulate the underwater friction-stir welding (FSW) process for dissimilar joining between aluminum and steel. Temperature profile, materials flow, intermixing during bonding under cooling medium were monitored via VOF verified according experimental data. effects processing parameters on formation intermetallic compounds (IMCs) at Al/St interface, microstructural characteristics, mechanical property weldments studied addressed. By...
In the present study, based on 12-unknown higher order shear deformation theory (HSDT), buckling and vibration analysis of FG-CNTRC rectangular plate are investigated for various types temperature distribution boundary conditions. Implementing Hamilton's principle, equations motion derived solved by adopting Navier solution simply supported conditions DQM method other Validation is carried out comparing numerical results with those obtained in open literature. Also, a detailed parametric to...
In this study, dissimilar sheets including AA3003 aluminum and A441 AISI steel were welded via cooling-assisted friction stir welding (FSW). Three different cooling mediums forced CO2, water, air employed, a non-cooled sample was processed to compare the condition with traditional FSW condition. The highest rate belongs CO2 lowest as FSW. best macrograph without any segregation at interface water-cooled poorest joint notable sample. exhibits smallest grain size due suppression of growth...
Buckling and crushing behavior of foam-core hybrid composite sandwich columns under edgewise compressive load is dealt in this study. Composite laminates with different stacking sequence configurations made glass Dyneema-woven fabrics AL 2024-T3 sheets were used combination polyvinyl chloride foam core to manufacture the specimens. Effects face sheet thickness configuration, slenderness ratio, boundary conditions, reinforcement through-thickness resin pins on buckling specimens investigated....
The effects of tilt angle (TTA), plunge depth (TPD) and offset (TO) tool in friction stir welding poly(methyl methacrylate) T-joint were investigated. To understand better the process parameter, thermomechanical simulation joint was assessed. results seem to show that at higher TPD TTA, frictional heat increases. Woven tissue structure line forms after sheets. distance woven layers affected by while TO do not significantly affect generation joint. best material flow adequate are generated 0...
Thin-walled tubes are widely used as energy absorbers in various vehicles and moving parts. The objective of this study is to investigate the absorption characteristics with corrugations different geometries, under lateral loading. In order produce corrugations, an innovative solution introduced. Quasi-static tests were conducted effect changing corrugation geometry (type amplitude). results show that have a higher mean crushing force which directly proportional number their amplitudes....
This paper reports the mechanical behavior of resin pin-reinforced composite sandwich panels made from polyvinyl chloride core and glass/epoxy face sheets under indentation a hemispherical indenter three-point bending loading conditions. The goal was to study effects reinforcing parameters such as number, arrangement, diameter through-the-thickness pins on maximum load, strength, energy absorption characteristics tested samples these results revealed that using reinforce foam led increase...
Dynamic behavior of a new class nanocomposites consisted metal foam as matrix and graphene oxide powders reinforcement is presented in this study the framework forced vibration. Graphene are dispersed through thickness plate made from material according to four various functionally graded patterns on basis Halpin-Tsai micromechanical homogenization method. Also, three kinds porosity distributions including two symmetric one uniform considered for matrix. As external effects, rested...