A5054350294- Hydrogen embrittlement and corrosion behaviors in metals
- Microstructure and Mechanical Properties of Steels
- Microstructure and mechanical properties
- Advanced materials and composites
- Fusion materials and technologies
- Welding Techniques and Residual Stresses
- Additive Manufacturing Materials and Processes
- Corrosion Behavior and Inhibition
- Metal and Thin Film Mechanics
- Water Quality Monitoring Technologies
- Membrane Separation Technologies
- Metal Alloys Wear and Properties
- Nuclear Materials and Properties
- Urban Heat Island Mitigation
- Thermal and Kinetic Analysis
- Electronic and Structural Properties of Oxides
- Innovative concrete reinforcement materials
- Surface Modification and Superhydrophobicity
- Advanced Materials Characterization Techniques
- Aluminum Alloys Composites Properties
- Extraction and Separation Processes
- Additive Manufacturing and 3D Printing Technologies
- Water Quality Monitoring and Analysis
- Materials Engineering and Processing
- Advanced Sensor and Energy Harvesting Materials
University of Science and Technology Beijing
2021-2023
Chongqing University
2017-2021
Technical University of Denmark
2021
University of Jinan
2018-2020
Guiyang University
2018
Guizhou University
2018
Leibniz-Institute for New Materials
2017
Shanghai Institute of Ceramics
2012
Chinese Academy of Sciences
2012
An insoluble layer is deposited on 904L in HF due to a preferential reaction between [F<sup>−</sup>] and the [Ni] from alloy. This deposit helps isolate aggressive ions base metal, while inhibits passivation of HF.
Tantalum and its alloys are regarded as equipment construction materials for processing aggressive acidic media due to their excellent properties. In this study, the influence of severe rolling (90%) on dissolution rate a cold-rolled Ta-4%W sheet in different directions was investigated during immersion testing corresponding mechanism discussed. The results show that sample is significantly lower than undeformed sample. corrosion resistance followed sequence “initial” < “90%-ND” “90%-RD”...
The effect of recrystallization annealing on corrosion behavior Ta-4%W alloy was studied. It is found that the deformed sample contains high dense dislocations and dislocation boundaries. During annealing, these boundaries are replaced by recrystallizing grains until fully recrystallized. Both anodic dissolution cathodic activity much more blocked. potential gradual shift towards negative values current density decrease, while polarization resistance increases after indicating enhanced...
In recent years, ceramic membranes have been widely used in the field of water and wastewater treatment by virtue their advantages over conventional technologies. this article, definition, classification characteristics membrane were introduced firstly. And then application technology various fields was highlighted. Finally, several opinions on development prospects raised.
One of the common features deformed face-centered cubic metals with medium to high stacking fault energy is formation geometrically necessary dislocation boundaries. The boundary arrangements in refractory body-centered crystal structure are, however, less well known. To address this issue a Ta-4%W alloy was cold rolled up 70% thickness present work. resulting deformation microstructures were characterized by electron back-scattering diffraction and each grain revealed using sample-frame...
In this paper, while ceramic membrane fouling and its causes were introduced, the calculation of resistance, analysis methods several common cleaning techniques summarized. process, some factors affecting effect also analyzed by enumerating cases, future development was prospected.
Gelation‐mediated phase separation is applied to prepare immiscible polymer bilayer films with an interlocking interface structure. Polymer systems consisting of copolymer urea and polydimethylsiloxane epoxy are selected demonstrate the feasibility. When fraction exceeds 25 wt%, well‐defined structures self‐form by a one‐pot casting method in which state fixed evaporation‐induced gelation. Microscopy studies resulting bilayers clearly reveal that form during construct. The lead enhanced...
Hot-stamping steel is a type of high-strength that mainly used in key safety components such as the front and rear bumpers, A-pillars, B-pillars vehicles. There are two methods producing hot-stamping steel, i.e., traditional process near net shape compact strip production (CSP) process. To assess potential risks using CSP, microstructure mechanical properties, especially corrosion behavior were focused on between CSP processes. The original produced by different. After quenching,...
Pipeline steel is a special type of used for transporting, example, oil and natural gas. This study focuses on X80-grade pipeline modified with the addition Nb Nb-V at different cooling rates (air or quenching) after hot rolling subjecting it to quenching tempering heat treatment. Based multiscale characterization techniques, effects microalloying rate microstructure, precipitation behavior, strengthening mechanisms were studied. The results showed that strengths quenched steels higher than...
Compared with the traditional treatment technologies, inorganic membrane technology is gradually becoming mainstream of oily and salty wastewater, but fouling has become bottleneck restricting development technology. In order to solve this problem, mechanism control strategies are introduced in paper. The atomic layer deposition preparation TiO 2 nanowires (NWs) film by impregnation method were mainly introduced, aiming provide a more reliable industrial research status field control.
Abstract Tantalum alloys are regarded as materials with great potential for challenging environments due to their exceptional mechanical properties, especially at high temperatures. To analyse deformation mechanisms and the relationship between microstructure strength, characterization of Ta-4%W during cold rolling from 10% 50% has been carried out by transmission electron microscopy combined backscatter diffraction investigations. The microstructural evolution was found follow same general...
用化学共沉淀法制备了Ce0.8Sm0.2O1.9-La9.33Si6O26纳米复合氧离子导电材料,通过X射线衍射和透射电子显微镜对合成材料的相结构进行了分析,利用交流阻抗分析测试研究了材料的离子导电性.结果表明,纳米复合材料的煅烧粉末的平均晶粒尺寸为20nm、烧结陶瓷体的平均晶粒尺寸为44nm;700℃时,纳米复合导电体的离子导电率为0.25Ω/cm;在整个测试温度范围内,纳米复合导电体比纯La9.33Si6O26提高了3个以上数量级,并高于纯相Ce0.8Sm0.2O1.9的导电性.
Ceramic membrane technique was a new and efficient technology for wastewater treatment used more widely in recent years. Controlling fouling the key method to ensure stable operation of ceramic membrane. In this paper, causes, influencing factors control methods were summarized. As one most effective means fouling, several common cleaning methods, such as physical cleaning, chemical ultrasonic combined introduced. And application presented too. Then future directions techniquresearching prospected.
With the rapid development of society and sustainable growth population, people's demand for water has been increasing continually. In consequence, more sludge was generated from purification process in waterworks. Treating utilizing efficiently safely becoming important. this paper, composition treatment municipal waterworks introduced firstly.And then comprehensive utilization problems among focused on. New methods as resources were explored at last.