A5002786197- Catalytic Processes in Materials Science
- Electrocatalysts for Energy Conversion
- Advanced Battery Materials and Technologies
- Carbon Nanotubes in Composites
- Gas Sensing Nanomaterials and Sensors
- Advancements in Battery Materials
- Advanced Battery Technologies Research
- Advanced Photocatalysis Techniques
- Dielectric materials and actuators
- Advanced Sensor and Energy Harvesting Materials
- Fuel Cells and Related Materials
- Catalysts for Methane Reforming
- Supercapacitor Materials and Fabrication
- Multiferroics and related materials
- Copper-based nanomaterials and applications
- Ferroelectric and Piezoelectric Materials
- Advanced battery technologies research
- High voltage insulation and dielectric phenomena
- Perovskite Materials and Applications
- Epoxy Resin Curing Processes
- Fluid Dynamics and Thin Films
- Thermal properties of materials
- Injection Molding Process and Properties
- MXene and MAX Phase Materials
- Electrochemical Analysis and Applications
Anhui University of Technology
2023-2024
Xi'an Jiaotong University
2023-2024
Zhejiang Normal University
2024
Shenyang University of Technology
2024
China University of Petroleum, East China
2024
China International Science and Technology Cooperation
2023
Harbin Engineering University
2023
Powerchina Huadong Engineering Corporation (China)
2023
Hebei University of Technology
2023
Florida A&M University - Florida State University College of Engineering
2005-2016
Li–air cells based on Li foil as an anode electrode, freestanding carbon nanotube/nanofiber mixed buckypaper air (cathode) and organic electrolyte were assembled. The electrode was made with single-wall nanotube (SWNT) nanofiber (CNF) without any binder. discharge capacity strongly dependent both the current density thickness of electrode. A high 2500 mAh/g obtained for at a ; however, it reduced to 400 when increased . For thick decreased from 1600 340 0.1 scanning electron microscope...
Electropolishing is the electrochemical process to remove metallic material from workpiece, in order obtain a smoother metal surface. It has found vast engineering applications many fields, such as food, medical, pharmaceutical and semiconductor industries. This review aimed provide readership with insightful understanding of electropolishing process, fundamental aspects well application aspects. The general electropolishing, including its definition, classic setup, fundamentals behind it...
Air electrodes, made with a mixture of carbon nanotube (CNT)/carbon nanofiber (CNF) and with/without α-MnO2 nano-rods, were prepared for Li-air cells. The charge capacity cyclability found to increase largely the cells catalyst; however, first cycle discharge capacities no different without catalyst. It was that cell mainly due oxygen deficiency from pinch-off diffusion channel by deposition product at air side electrode. Electrochemical impedance spectra cycles demonstrated transfer...
Abstract Single‐walled carbon nanotubes (SWNTs) are functionalized through both covalent and noncovalent bonding approaches to enhance dispersion interfacial bonding. The coefficient of thermal expansion (CTE) the functionalized‐SWNT‐reinforced epoxy composites measured with a mechanical analyzer (TMA). Experimental results indicate that changes glass‐transition temperature ( T g ) in SWNT–polymer dependent upon functionalization methods. CTE below nanocomposites 1 wt % loading is...
Abstract This paper presents a novel redesign approach that allows integrating environmental requirements into product development, taking account cost and customer preferences. The proposed methodology the identification of improvement options study effect incorporation these has over other traditional requirements. However, for improvements to be feasible from company perspective, market environmentally friendly products must exist where customers are willing pay such products. primary...
In the aerospace field, riveting process is one of main methods for connecting Carbon Fiber Reinforced Polymer/Plastic (CFRP). During process, components are prone to problems such as damage CFRP hole walls and reduction in joint strength. To this end, paper proposes two new bushing structures based on riveting. The behavior mechanical properties composite materials under three methods: non-bushing, non-boss bushing, boss were compared. Furthermore, tensile hysteretic different studied....
Current geometric dimensioning and tolerancing (GD&T) standards dictate that the geometry of a cylindrical manufactured part should be characterized in terms its roundness, straightness, cylindricity diameter. However, define form errors using maximum peak-to-valley values – very simplistic description. As result, measurements based on GD&T definitions for parts are ineffective identifying diagnosing error sources manufacturing process. This paper introduces new scheme application to...
Abstract Due to the increasing variations in raw materials and manufacturing processes, composite processes have more part-to-part compared with metal processes. To improve part quality consistency, tooling design optimisation is an imperative step for addressing stochastic behaviour of This paper presents approach typical technique resin transfer moulding (RTM), which minimises sensitivity mould uncertain material properties by choosing appropriate locations injection gates vents. proposes...
Conflicts between the existing temperature-resistant ink and printing window currently prevent electrohydrodynamic (EHD) printed thin film temperature sensors from achieving both fine line width a higher measurement limit simultaneously. In this study, we propose method to adjust AgNPs prepare with micro dimensions enhanced capabilities. The involves leveraging solubility of Polyester resins (PR) in alcohol-ether solvent incorporate PR into nano-silver solution same system. This allows for...