A5008083902- Advanced ceramic materials synthesis
- Catalytic Processes in Materials Science
- Catalysts for Methane Reforming
- Thermal properties of materials
- Fiber-reinforced polymer composites
- Chemical Looping and Thermochemical Processes
- Graphene research and applications
- Carbon Dioxide Capture Technologies
- Catalysis and Hydrodesulfurization Studies
- Advanced Chemical Sensor Technologies
- Nanomaterials for catalytic reactions
- Supercapacitor Materials and Fabrication
- Arctic and Antarctic ice dynamics
- Additive Manufacturing and 3D Printing Technologies
- Wave and Wind Energy Systems
- Freezing and Crystallization Processes
- Radiative Heat Transfer Studies
- Thermal Radiation and Cooling Technologies
- Concrete and Cement Materials Research
- Aluminum Alloys Composites Properties
- Advancements in Solid Oxide Fuel Cells
- Building Energy and Comfort Optimization
- Analytical Chemistry and Sensors
- Material Properties and Applications
- Mesoporous Materials and Catalysis
Nanjing Normal University
2023
Dalian University of Technology
2012
Hainan University
2012
Myongji University
2004-2006
Integrated CO2 capture and utilization (ICCU) has been regarded as an innovative strategy to realize large-scale emission reduction. The rational design of robust dual-function materials (DFMs) the optimization operating parameters are essential for intensification ICCU process. In this work, Ni-CaO DFMs pellets with Ni loadings varying in 1–20 wt % range prepared CO production via integrated reversed water gas shift (RWGS) reaction. effect loading on structure–reactivity relationships is...
Nanoporous TiO 2 powders were prepared following a two-step method.The highly ordered uniform nanotube arrays first grown by the electrochemical anodization of Ti metal sheet and subsequently, mechanically milled to obtain porous .The obtained nanoporous sample contains nanotube-like particles with length around 400 nm inner diameter ~100 also some near-spherical single crystals 10 nm.The sensing properties assynthesized based resistive-type chemical sensor formaldehyde demonstrated.The...
Emissive carbon coating was prepared using a black powder and phenolic resin binder suspension. Interior of an alumina tube with emissivity 0.75 coated the emissive its energy saving performance investigated vacuumed up to 1000°C. The cavity temperature carbon-coated embedded in electrically heated furnace always higher than that uncoated one for same surface tube. difference between increased At 1000 °C, reached about 20°C. Heating raise from ambient 1000°C at constant heating rate 5°C/min...
Porous ceramic fiber composites were coated with pyrolytic carbon by the decomposition of propane in a nitrogen atmosphere at 900°C. The amount coating was varied through adjusting deposition time to tailor electrical conductivity carbon-coated composites. and thermal measured room temperature using two-point method hot-wire method, respectively. Up 7 wt% carbon, σ is linearly increased 0.02 S/cm well fitted effective according parallel rule mixture eff = Σ Χ i ·σ c= 20 .The uncoated range...
Porous composites containing ceramic fiber have been developed for the fabrication of SOFC seals. They were fabricated using glass powder and alumino-silicate chopped fibers. Effect mixing ratios on leak rates strength composite seals was investigated. In addition, seal performance commercial glasses compared with that SiO2-BaO-B2O3 synthesized in this work. The rate 55 vol% seven times higher than one 75 glass. flexural reduced to fourth initial value as porosity increased from 1 29%....
Porous ceramic fiber composites were coated with pyrolytic carbon by the decomposition of infiltrated phenolic resin in a nitrogen atmosphere at 800. The amount coating was varied to tailor electrical conductivity carbon-coated composites. and thermal measured room temperature using two-point method hot-wire one, respectively. Up 30 wt% carbon, σ shows linearly increasing tendency is fitted effective according parallel rule mixture σeff = ΣΧi ·σi an σc= 0.42 S/cm. range 0.05-0.08 W/mK...
Electrically conductive porous Si/SiC fiber media were prepared by infiltration of liquid silicon into carbon preforms. The series rule mixture for the effective electrical conductivity was applied to disc shaped samples estimate their content, and porosity. estimated assuming sample as a plate equivalent geometry, i.e., same thickness, electrode distance volume. As volumetric content in increases from 0.026% 0.97%, 0.17 S/cm 2.09 S/cm. porosity measured Archimedes principle range 75~83%...