A5057489644- Polymer crystallization and properties
- Polymer Nanocomposites and Properties
- Electronic Packaging and Soldering Technologies
- Mechanical Behavior of Composites
- 3D IC and TSV technologies
- Epoxy Resin Curing Processes
- Fiber-reinforced polymer composites
- biodegradable polymer synthesis and properties
- X-ray Diffraction in Crystallography
- Natural Fiber Reinforced Composites
- Tribology and Wear Analysis
- Crystallization and Solubility Studies
- Clay minerals and soil interactions
- Synthesis and properties of polymers
- Metal Forming Simulation Techniques
- Advanced Sensor and Energy Harvesting Materials
- Material Properties and Processing
- Aluminum Alloys Composites Properties
- Electrostatic Discharge in Electronics
- Organic Electronics and Photovoltaics
- Photonic and Optical Devices
- Recycling and Waste Management Techniques
- Integrated Circuits and Semiconductor Failure Analysis
- Metallurgy and Material Forming
- Advanced Fiber Optic Sensors
Shanghai Jiao Tong University
1997-2025
University of Hong Kong
2012-2024
Hong Kong University of Science and Technology
2012-2024
Zhejiang Sci-Tech University
2024
East China University of Science and Technology
2024
Shanghai Ninth People's Hospital
2022-2024
Shandong First Medical University
2024
Third Affiliated Hospital of Southern Medical University
2024
National University of Defense Technology
2024
Huanghe Science and Technology College
2024
Epoxy/clay nanocomposites with a better exfoliated morphology have been successfully prepared using so-called "slurry-compounding" process. The microstructures of the (epoxy/S-clays) were characterized by means optical microscopy and transmission electron (TEM). It was found that clay highly uniformly dispersed in resulting nanocomposite. Characterizations mechanical fracture behaviors revealed Young's modulus increases monotonically increasing concentration while toughness shows maximum at...
We propose an open-loop and a closed-loop stochastic event-triggered sensor schedule for remote state estimation. Both schedules overcome the essential difficulties of existing in recent literature works where, through introducing deterministic event-triggering mechanism, Gaussian property innovation process is destroyed which produces challenging nonlinear filtering problem that cannot be solved unless approximation techniques are adopted. The proposed eliminate such approximations. Under...
The osteochondral defects (OCDs) resulting from the treatment of giant cell tumors bone (GCTB) often present two challenges for clinicians: tumor residue leading to local recurrence and non-healing OCDs. Therefore, this study focuses on developing a double-layer PGPC-PGPH scaffold using shell-core structure nanofibers achieve "spatiotemporal control" treating OCDs caused by GCTB. It addresses key challenges: eliminating after excision stimulating regeneration in OCD cases. With shell layer...
Abstract The essential work of fracture method is explored. was used to determine the toughness a series toughened polymer blends and crack resistance thin ductile film, which could not be tested using J ‐integral method. A comparison between specific carried out test equivalence two methods. effects geometry on plane‐stress/plane‐strain transition were studied. It has been shown that material constant, independent sample geometry, equivalent critical ‐integral. found depend nature tested....
The effect of fiber surface pretreatment on the interfacial strength and mechanical properties wood fiber/polypropylene (WF/PP) composites are investigated. results demonstrate that conditions significantly influence fiber–matrix bond, which, in turn, determines composites. WF/PP composite containing fibers pretreated with an acid–silane aqueous solution exhibits highest tensile among materials studied. This observation is a direct result strong bond caused by acid/water condition used...
Considerable improvement in the impact toughness of an annealed polypropylene (PP) nanocomposite containing CaCO3 nanoparticles was achieved and its toughening mechanism investigated. The prepared by melt-blending PP a batch mixer. Injection-modeled tensile bars were at 150 °C for 2 h prior to tests. Young modulus yield stress found increase after annealing. What is more, had much higher than unannealed counterpart. average Izod strength °C-annealed nanocomposite, 20 wt % (7.8 vol %) coated...
Piranha solution is shown to be an effective agent in activating the surface of HNTs for silanization modification.
Epoxy/clay nanocomposites with a high degree of exfoliation were achieved using so-called "slurry-compounding" process which the dispersed state clay in water can be successfully transferred to an epoxy matrix. In this sodium montmorillonite was first exfoliated and suspended water. This suspension further treated acetone form clay-acetone slurry followed by chemical modification silane. The modified then mixed extensively epoxy/nanoclay composites. It has been shown that morphologies before...
Abstract This article discusses the methods of interface modification composites based on raw wood flakes and high‐density polyethylene (HDPE) effects these modifications composite properties. An HDPE matrix was modified by a reaction with maleic anhydride (MA) in twin‐screw extruder then compounded to produce wood–polyethylene composites. Wood were silane coupling agent an aqueous medium before being silane‐modified WPCs. Differential scanning calorimetry Fourier transform infrared...