A5100368229- Asphalt Pavement Performance Evaluation
- 3D Printing in Biomedical Research
- Infrastructure Maintenance and Monitoring
- Structural Behavior of Reinforced Concrete
- Catalysis and Hydrodesulfurization Studies
- Carbon dioxide utilization in catalysis
- Lubricants and Their Additives
- Concrete Corrosion and Durability
- Smart Materials for Construction
- Catalysis for Biomass Conversion
- Gas Sensing Nanomaterials and Sensors
- Structural Load-Bearing Analysis
- Robotics and Sensor-Based Localization
- Extraction and Separation Processes
- Additive Manufacturing and 3D Printing Technologies
- Innovative concrete reinforcement materials
- Catalytic Processes in Materials Science
- Tribology and Wear Analysis
- Advancements in Battery Materials
- Metal-Organic Frameworks: Synthesis and Applications
- Polymer Nanocomposites and Properties
- Nanomaterials for catalytic reactions
- Transition Metal Oxide Nanomaterials
- Microstructure and Mechanical Properties of Steels
- Advanced Vision and Imaging
Wuhan University of Technology
2012-2024
Kunming University
2017-2024
Shaoxing University
2024
Shanxi Medical University
2024
Wuhan University
2020-2024
Chinese Academy of Sciences
2015-2024
Shenyang Aerospace University
2024
Computer Network Information Center
2024
China National Petroleum Corporation (China)
2023
Liaoning Normal University
2023
The composites of graphene oxide (GO) nanosheets fabricated by α-Fe2O3 nanorods were prepared through a facile hydrolysis route. As-synthesized incorporated into GO in the observed with diameters 3–5 nm and lengths 15–30 nm. formation mechanism anchoring onto was proposed as intercalation adsorption iron ions surface nanosheets, followed nucleation growth nanorods. Tribological properties nanorod/GO lubricating oil additive investigated employing ball–plate tribotester. It is shown that...
A reduction in the particle size is expected to improve properties and increase application potential of high-entropy alloys. Therefore, this study, a novel sol-gel autocombustion technique was first used synthesize The average grain prepared nanocrystalline CoCrCuNiAl alloys showed 14 nm with an excellent uniform dispersion, exhibiting distinct magnetic behavior similar superparamagnetic behavior. We show that metal nitrates form (Co,Cu,Mg,Ni,Zn)O oxides, then situ reduce by reducing gases,...
To promote the comprehensive utilization of solid waste in highway engineering, asphalt rubber hot mixture (ARHM-13) was prepared with steel slag and SBS/CR modified asphalt. The pavement performance basalt mixtures, including Marshall stability, moisture susceptibility, high temperature low performance, were evaluated laboratory. Combined project case trial section Beijing-Qinhuangdao Expressway, compactness, flatness, skid resistance seepage pavements tested. And volatile organic compounds...
A 2-D laser rangefinder (LRF) and a camera are widely applied in various mobilized systems, such as autonomous robot unmanned ground vehicle. Integration of these two types sensors promotes new measurement technology. Extrinsic calibration is crucial basically the first step to fuse image data. The chessboard-plane-based method one most popular ones, which requires at least five plane-input (five shots). Vasconcelos et al. recently reduced number shots from three derived minimal solution....
The objective of this study is to get a fundamental understanding role surface oxygen‐contained functional groups (OCFG) in adsorptive denitrogenation (ADN) liquid hydrocarbons over activated carbon, and thus improve the ADN performance carbon through modification chemistry carbon. A set samples with different amount distribution OCFG was prepared by oxidative thermal treatment commercial carbons were characterized temperature‐programmed desorption coupled mass spectrometry for concentration...
A new poly(ionic liquid) of N,N-methylenebisacrylamide (MBA)-crosslinked-poly(4-vinylbenzyltriethylammonium hexafluorophosphate)(MBA-crosslinked-P[VBTEA][PF6]) is prepared through the ion exchange KPF6 with precursor MBA-crosslinked-P[VBTEA][Cl]; synthesized by 4-vinylbenzyltriethylammonium chloride and MBA via inverse suspension polymerization. MBA-crosslinked-P[VBTEA][PF6] a thermally stable (decomposes at nearly 300°C) porous (apparent porosity 64.3% specific surface 39.12 m2/g) polymer...
The rapid advancement in the fabrication and culture of