A5063286039- Hydrocarbon exploration and reservoir analysis
- Petroleum Processing and Analysis
- Recycling and utilization of industrial and municipal waste in materials production
- Advanced ceramic materials synthesis
- Corrosion Behavior and Inhibition
- Hydrogen embrittlement and corrosion behaviors in metals
- Concrete Corrosion and Durability
- Concrete and Cement Materials Research
- Marine Sponges and Natural Products
- Analytical Chemistry and Chromatography
- Adsorption and biosorption for pollutant removal
- Membrane Separation Technologies
- Seaweed-derived Bioactive Compounds
- Analytical Methods in Pharmaceuticals
- Traditional and Medicinal Uses of Annonaceae
- Phase Equilibria and Thermodynamics
- Pharmacological Effects and Assays
- Geochemistry and Geologic Mapping
- Innovations in Concrete and Construction Materials
- Phosphorus and nutrient management
- Nanomaterials for catalytic reactions
- Zeolite Catalysis and Synthesis
- Diatoms and Algae Research
- Phytochemistry and Bioactive Compounds
- Electrochemical sensors and biosensors
Cadi Ayyad University
2017-2024
National School of Architecture
2020-2023
École Nationale Supérieure d'Architecture de Strasbourg
2023
University of Hassan II Casablanca
2004-2020
Laboratoire des Biomolécules
2010-2018
École Nationale Supérieure de Statistique et d'Économie Appliquée
2016
École Nationale de la Statistique et de l'Administration Économique
2016
Université Hassan II Mohammedia
2005-2014
Laboratoire de Chimie Organique
1999-2003
In wastewater treatment, the application of ceramic membranes has gained significant attention due to their potential for highly effective filtration. These are typically produced using methods such as spin coating, dip-coating, and spray coating. However, these techniques have limitations when applied large-scale industrial applications high cost, time consuming process, difficulty control. Moreover, obtaining a complete uniform coating requires several attempts. This research demonstrates...
The influence of the removal carbonates on ceramic properties made Moroccan red clay as a main material and tea waste pore-forming agent, has been investigated. ATD-TG, dilatometry, dimensional changes, weight loss, water absorption, open porosity, bulk density, flexural indirect tensile strengths were assessed at different firing temperatures within range 900-1150 ◦C. SEM was used to evaluate microstructures fired samples, while XRD study phase evolution. At varying temperatures, materials...
The effect of extract brown alga Bifurcaria bifurcata (Bb) on the corrosion steel in 1 M HCl solution was studied using weight loss, potentiodynamic, and polarization resistance measurements. Experimental data revealed that Bb acted as an inhibitor acid environment. a mixed-type inhibitor, predominating anodic at higher concentration. It found inhibition efficiency increased with increase carbon also investigated by infrared UV-visible spectrophotometry to obtain information bonding...
Porous ceramics were prepared by a solid state process from mixture of clay and 20 wt% banana peels (BPs). BPs used as an eco-friendly pore-forming agent. Compacted pellets the dry calcined at three sintering temperatures, 900, 1000, 1100 °C, for 2 h. The effect temperature on ceramic properties, such apparent porosity mechanical strength, was examined, increase in 900 to °C yielded porous with decreased increased strength. To obtain (40.2 vol% porosity) sufficient indirect tensile...
The aim of the present work is to characterize phosphate sludge from area Youssoufia (rich in CaO ∼ 31%) and study its thermal behavior alone when mixed with clay Safi (Morocco). This may contribute valorization as an alternative raw material for ceramic industries. evolution phases during treatment sludge, sludge–clay mixtures at different mass ratios (25 wt%, 50 75 wt%) was performed levels temperatures 600 1120 °C. Mineralogical analysis by X-ray diffraction (XRD) showed that mainly...
Within the Moroccan natural resources valorisation scheme, new adsorbents have been prepared from oil shale by chemical and physical activation processes.The process authors developed in this study give effective adsorbent materials.In view of physico-chemical properties these materials application to treatment water loaded with a metal (Cr 6+ ion) or organic (methylene blue (MB)) pollutant, it is concluded that at low temperature (250 °C) affords best material.The material's yield good...