A5075725452- Particle Accelerators and Free-Electron Lasers
- Architecture and Computational Design
- Robotics and Automated Systems
- Laser Design and Applications
- Computability, Logic, AI Algorithms
- Manufacturing Process and Optimization
- Particle accelerators and beam dynamics
- Lubricants and Their Additives
- BIM and Construction Integration
- Context-Aware Activity Recognition Systems
- Spacecraft and Cryogenic Technologies
- Modular Robots and Swarm Intelligence
- Design Education and Practice
- Scientific Computing and Data Management
- Network Time Synchronization Technologies
- Ionic liquids properties and applications
- Data Quality and Management
- Distributed and Parallel Computing Systems
- Sustainable Design and Development
- Real-Time Systems Scheduling
- Power Line Inspection Robots
- Remote Sensing and LiDAR Applications
- Construction Project Management and Performance
- Advancements in Photolithography Techniques
- Evolutionary Algorithms and Applications
Faculty of Design
2021
University of Toronto
2021
Intel (United Kingdom)
2019
Thomas Jefferson National Accelerator Facility
2017
Singapore University of Technology and Design
2015
Moscow Institute of Thermal Technology
2015
McGill University
1997
Australian National University
1997
Louisiana State University
1997
University of Oxford
1997
Digital fabrication machines (such as laser cutters or 3D printers) can be instructed to produce any part geometry within their application space. However, machines' spaces are not easily modified extended. How we enable the production of application-specific computer-controlled by machine building novices? facilitate rapid prototyping tools? We propose a novel set modules, Cardboard Machine Kit, for construction digital machines. These open-source modules implemented using cardboard frames,...
The IEEE family of standards referred to as Time Sensitive Networking (TSN) is gaining popularity in many real-time embedded applications, including industrial automation and automotive. Based on a synchronized clock at the network layer, TSN aim deterministic behavior message communication over an Ethernet. However, data access time between CPU its interface may be affected by contention for shared resources buses each node. Any jitter this final segment path can have negative impact...
Journal Article "The suffolk mercury." Get access James Coleman 122, High Street, Bloomsbury Search for other works by this author on: Oxford Academic Google Scholar Notes and Queries, Volume s2-X, Issue 244, 1 September 1860, Page 168, https://doi.org/10.1093/nq/s2-X.244.168b Published: 01 1860
After three decades of digitally fabricating the world's wildest architecture, Zahner's R&D team discuss trials, tribulations, and a path to personalized production.
Hardware and software are disjoint in their representations, production methods, validation. Machine design, machine building, control have historically taken place separately, correspondingly, tools not well integrated systems addressing an automation or fabrication need.
In 2012 Jefferson Laboratory's energy recovery linac (ERL) driven Free Electron Laser successful completed a transmission test in which high current CW beam (4.3 mA at 100 MeV) was transported through 2 mm aperture for 7 hours with losses as low 3 ppm. The purpose of the run to mimic an internal gas target DarkLight* - experiment designed search dark matter particle. ERL not again until late 2015 brief re-commissioning preparation next phase DarkLight. intervening years, FEL rebranded Low...
Four factors that largely determine the end product obtained when cement andwater are mixed chemical composition of cement, fineness towhich is ground, amount mixing water used, and procedureused in slurry. In order to study effect two thesefactors, other two, method mixing, keptconstant, leaving as variables water-cement ratio. Through years experimentation usage it has been well established thatthe reduction clinker a very fine state by grinding improve itscementing value, principally...
Architectural manufacturing is a balancing act between production facility and custom fabrication shop.Each project Zahner takes on different from the last, not likely to repeat.This means that workflows are designed deployed for each individually.We present Flash Manufacturing, methodology we employ in of architectural elements cutting-edge computationally sophisticated buildings.By remixing techniques spaces able meet novel challenges posed by fabricating assembling hundreds thousands...
Cabry family Get access James Coleman Search for other works by this author on: Oxford Academic Google Scholar Notes and Queries, Volume s2-V, Issue 115, 13 March 1858, Page 215, https://doi.org/10.1093/nq/s2-V.115.215f Published: 1858
course Share on Siggraph studio workshop: how to make almost anything Authors: Nadya Peek MIT MITView Profile , James Coleman Authors Info & Claims SIGGRAPH '15: 2015: StudioJuly 2015 Article No.: 36Pages 1–48https://doi.org/10.1145/2785585.2792721Published:31 July 2015Publication History 0citation91DownloadsMetricsTotal Citations0Total Downloads91Last 12 Months3Last 6 weeks1 Get Citation AlertsNew Alert added!This alert has been successfully added and will be sent to:You notified whenever a...
Summary not available at press time.
Book Reviews Get access FRED T. SCHREIERHuman Motivation. Glencoe, Ill., Free Press, 1957, 256 pp., $5 JAMES COLEMAN Johns Hopkins University Search for other works by this author on: Oxford Academic Google Scholar Public Opinion Quarterly, Volume 23, Issue 3, FALL 1959, Pages 456–457, https://doi.org/10.1086/266897 Published: 01 January 1959