A5031117568- Metal and Thin Film Mechanics
- High-Temperature Coating Behaviors
- Intermetallics and Advanced Alloy Properties
- Advanced materials and composites
- Corrosion Behavior and Inhibition
- Titanium Alloys Microstructure and Properties
- Advanced Surface Polishing Techniques
- High Entropy Alloys Studies
- Metal Alloys Wear and Properties
- Advanced machining processes and optimization
- Advanced Machining and Optimization Techniques
- Fusion materials and technologies
- Advanced X-ray and CT Imaging
- Magnesium Alloys: Properties and Applications
- Advanced X-ray Imaging Techniques
- Medical Imaging Techniques and Applications
- Hydrogen embrittlement and corrosion behaviors in metals
- Diamond and Carbon-based Materials Research
- Nuclear Materials and Properties
- MXene and MAX Phase Materials
- Ion-surface interactions and analysis
- Robotics and Sensor-Based Localization
- Soft Robotics and Applications
- Medical Image Segmentation Techniques
- Advanced battery technologies research
Nanjing University of Aeronautics and Astronautics
2015-2024
Harbin Institute of Technology
2009-2024
Ministry of Industry and Information Technology
2018-2024
Southern University of Science and Technology
2023-2024
Changzhou University
2018
University of Wollongong
2017
Shanghai Jiao Tong University
2016
Beihang University
2007-2014
Abstract Graphite felt is commonly used in redox flow batteries, but the low specific surface area and poor catalytic activity cause unsatisfactory mass transfer reaction kinetics. Here, nitrogen‐doped vertical graphene in‐situ grown on graphite via a metal‐free chemical vapor deposition method, which exhibits high remarkable due to abundant exposed high‐density sharp edges nitrogen doping. Multiphysical simulations reveal that vertical‐standing nanostructure promotes accessibility of...
In this article, samples of phenolic resin reinforced with graphene oxide were prepared. Mechanical properties the composite tested. Dynamic mechanical analysis, Fourier transform infrared spectroscopy, Differential scanning calorimetry, and thermogravimetric analysis employed to study in varied temperatures infer influence on thermal performance resin. The results show that addition resulted a significant improvement elastic modulus resin; Young's modulus, tensile strength increase along...
ABSTRACT Porous materials have specific properties, such as high surface area, permeability, lightweight, and low thermal conductivity. In foaming process of thermoplastics, melt viscosity is indispensable. Neither poly(lactic acid) (PLA) nor poly(butylene succinate) (PBS) has sufficient viscosity. this manuscript, Organophilic montmorillonite (OMMT) was employed to improve the performance PLA/PBS blends. Mechanical tests were undertaken compare change foams before after reinforcement OMMT....
In this article, samples of phenolic foam reinforced with graphene oxide were prepared. Gel time resole was tested to choose the appropriate foaming agent. Friability and Mechanical properties composite tested. Dynamic mechanical analysis (DMA) employed study in varied temperatures. The results show that gel is increased 68.2% by using 0.5% oxide; n ‐hexane more fitting as blowing agent for foam; Impact toughness increase along content. It not obvious when amount lower than 0.3% there a...
This work proposes an in-plane gradient flow field design which enhances the under-rib convections for redox batteries. Furthermore, generalized structured approaches have been proffered future scientific research.
In this study, the role of working fluid in electrical discharge machining (EDM) was investigated based on its conductivity. The function gas bubble material removal process studied by comparing crater that formed water with air discharge. mechanism for EDM water-based proposed analyzing voltage. Experiments were conducted to learn influence parameters and conductivity forming process. detected waveform demonstrated effect electrolytic reaction could be controlled changing fluid. This study...
In order to improve corrosion resistance of pure titanium in strong acid solution, the tantalum modified layer was formed on surface by double glow plasma tantalumising. The modification comprised deposition and diffusion layer, which metallurgically adhered substrate. Tantalum element decreased with case depth. HCl solution investigated weight loss method electrochemical measurements, morphology (SEM) studied SEM X-ray diffraction. annual rate only 12 21% 10 20 wt-% respectively, still...
The Al–Zn–Si coating was deposited on Q235 steel by thermal spray technology. corrosion behaviour of the in simulated marine environments has been investigated through neutral salt test (NSS) and electrochemical test. Furthermore, microstructure morphologies were detected means scanning electron microscopy, energy dispersive spectroscopy X-ray diffraction. results showed that exhibited a dense homogeneous lamellar without obvious defects. There different periods environment, such as...