- Additive Manufacturing and 3D Printing Technologies
- Additive Manufacturing Materials and Processes
- Injection Molding Process and Properties
- Innovations in Concrete and Construction Materials
- Manufacturing Process and Optimization
- Cellular and Composite Structures
- Surface Roughness and Optical Measurements
- Advanced Manufacturing and Logistics Optimization
- Dental materials and restorations
- Gas Dynamics and Kinetic Theory
- Welding Techniques and Residual Stresses
- Laser Material Processing Techniques
- Heat transfer and supercritical fluids
- Spacecraft and Cryogenic Technologies
- Conservation Techniques and Studies
- Advanced machining processes and optimization
- Ancient and Medieval Archaeology Studies
- Museums and Cultural Heritage
- Space Satellite Systems and Control
- 3D Surveying and Cultural Heritage
- 3D Printing in Biomedical Research
- Dental Radiography and Imaging
- Engineering Applied Research
- Recycling and Waste Management Techniques
- Heat Transfer and Optimization
Istanbul Technical University
2024-2025
Fatih Sultan Mehmet Waqf University
2019-2023
Mimar Sinan Güzel Sanatlar Üniversitesi
2021-2022
Gyroid structures exhibit significant potential in the fields of lightweight structural design, heat transfer, energy absorption, and biological applications. The use gyroid for implants dentistry is currently not sufficiently widespread. research encompasses compression testing, cellular investigation using a digital microscope, application artificial neural networks (ANNs) data gained from test. ANN study test phase which geometries are addressed by dental three-point bending tests novel...
In the production of geometries that traditional methods cannot produce, it is seen additive manufacturing (AM) technology, which has come to fore, been used extensively in conformal cooling channel (CCC) applications recent years. This study, conducted within scope CCC's use applied mold cores automotive industry plastic part production, aimed reduce cycle time injection printing process. The v1 geometry, gives analysis results for ideal quality from developed with three different design...
Unmanned aerial vehicles are expected to complete their missions even in adverse weather conditions. Overheating the engine area may occur, particularly at high speeds due using full throttle. Another design factor that affects endurance duration and maximum take-off weight is of unmanned vehicle heat exchanger. In this paper, a new type air-cooled fuel cooler exchanger proposed reduce total by increasing cooling performance through flexibility offered additive manufacturing. The printed...
Purpose The purpose of this article is on the functional usability metal additive manufacturing (AM) direct laser sintering (DMLS) production technology process parameters in construction industry. In study, advantages thermal optimization and weight reduction case use foam metals obtained by changing hatch distance parameter, facade panels architectural field are revealed. Design/methodology/approach methods study; small scaled with nine different parameters, determination change infrared...
Aluminum-based cellular structures are gaining a huge traction in several applications, including lightweight aircraft, military equipment, and heat exchangers. With additive manufacturing, the fabrication of complex periodic with any unit cell form, size, volume fraction has become lot easier, allowing for more investment, research, attention from both academia industry. The aim research was to assess manufacturability performance AlSi10Mg generated using laser powder bed fusion process....
İnceliğin estetiğe, estetiğin mimariye dönüştüğü kuşevi, yaşadığımız coğrafyada,yüzyıllar öncesi temelleri atılmış bir geleneğin, kültürel değerin günümüze ulaşan, kaybolmasındanendişe duyulan izleri olarak görülebilir. Kuşevi geleneği, teknolojik gelişmeler,değişen toplum ihtiyaçları ve üretim teknikleri gibi bazı sebeplerle kaybolmayayüz tutmuş, mevcut örnekler korunamaz olmuştur. Bu makalede, kaybolmakta olan birgeleneğin, yeni teknolojilerin kullanılması ile tekrar canlandırılması...
In this study, the design, analysis, and production of an unmanned aerial vehicle (UAV) was carried out using SLS (Selective Laser Sintering) technology. Herein, a multidisciplinary project realized on four different aircraft models supported by CFD analysis results during taxing were compared flow parameters. We observed that according to numerical design model 4 most suitable one among tested models, which then further utilized for viability, in-flight process. Finally, actual flight test...
Bu çalışma, mimarlık alanında kullanılan eklemeli imalat teknolojileri konusunda gerçekleştirilen bir derleme çalışmasıdır. Temel olarak, imalatın alanındaki uygulama alanlarını, belirli sistematik içerisinde ele alan araştırma, gerek literatürde yer örnekler, gerekse uygulamaları bulunan yeni teknolojiler hakkında bilgi vermeyi amaçlamaktadır. Çalışmada, karşılaştırmalı olarak incelenen üretim teknolojilerinin güçlü ve zayıf yönleri, sistemlerin kullanım alanları, sistemlerde malzemeler,...
Abstract In this study, a novel classification model is proposed to estimate surface roughness for the parts produced in an industrial additive manufacturing technology. The focused on selective laser sintering (SLS) technology based polyamide 12 powder applications. A comprehensive dataset designed simulate production and manufactured at SLS machine positioning strategy random positions test robustness of model. Deep Neural Networks (DNN) with hyperparameters problem. Benchmark results show...
It can be said that today's civil aviation basics began to laid in the 1950s. This date is also important as period which rules are being written and at same time, some system solutions produced by testing methods of cargo loading. The clip used these loading systems will subject our article. In this context, development process clip, started 1953 until today, examined light patent applications period; Afterwards, alternative clip-on work current V2 V3 models design analysis model included....