This paper shows the novel approach of Taguchi-Based Grey Relational Analysis Ti6Al4V Machining parameter. metal matrix composite has been fabricated using powder metallurgy route. Here, all components TI6Al4V machining forces, including longitudinal force (Fx), radial (Fy), tangential (Fz), surface roughness and material removal rate (MRR) are measured during facing operation. The effect three process parameters, cutting speed, tool feed depth, is being studied on matching responses....

Properties such as superior specific strength, being imponderous, and the ability to reprocess are key features that have drawn attention magnesium. In last few years, applications automotive, aerospace, medical been seeking light-weight equipment, materials required for making them. These demands were matched by developing metal matrix composites with magnesium a base reinforced carbon nanotubes (CNTs), grapheme nanoplatelets (GNPs), or ceramic nanoparticles. CNTs adopted high-strength...

Equal channel angular pressing (ECAP) technique can perform bulk deformation with nanostructured microstructures in materials. In this study, three-dimensional (3D) finite element simulation and experimentations were performed on Al-alloy. Both experimental studies conducted under same boundary condition, i.e. different processing temperature. The results from both computational analysed validated comparing the effect obtained microstructure of ECAPed Al-6061. FEM analysis was carried out to...

Magnesium alloys are widely employed in various applications due to their high strength-to-weight ratio and superior mechanical properties as compared unalloyed Magnesium. Alloying is considered an important way enhance the strength of metal matrix composite but it significantly influences damping property pure magnesium, while controlling rate corrosion for Mg-based material remains critical biological environment. Therefore, essential reinforce magnesium alloy with a suitable alloying...

Brackets are the load-bearing components in a satellite. The current age of satellites comprises specific brackets that set out as link between bodies satellite, reflector parts, and feeder facilities mounted at its upper end. used to carry loads satellite body frame, supporting elements, batteries, electronic goods. article explicates various aircrafts. strength bracket is utmost importance since it an important load member several assemblies aircraft satellites. In addition mechanical...

Indagation in the sphere of nanoparticle utilisation has provided commendatory upshots discrete areas application varying from medicinal use to environmental degradation alleviation. This study incorporates alumina nanoparticles as additives diesel and biodiesel blends. The prime objective present was scrutinisation denouement Al2O3 incorporation diesel–biodiesel blends on a engine’s performance emission characteristics. Test fuel samples were prepared by blending different proportions...

This paper explores theories of motivation, including instinct theory, arousal incentive intrinsic extrinsic the ARCS model, self-determination expectancy-value and goal-orientation theory. Each theory is described in detail, along with its key concepts, assumptions, implications for behavior. Intrinsic suggests that individuals are motivated by internal factors like enjoyment satisfaction, while external rewards social pressure drive Arousal says to feel motivated, people try keep an...

The conventional technique of materials design and discovery relies on experimentation complex computational methods. sheer number present makes testing each one for specific properties application the entire process time resource intensive. This has resulted into Machine Learning (ML) to gain popularity in domain science revolutionise accelerate process. Data-driven approaches such as these can be applied narrow down which we apply tradition methods, thus cutting both cost development new...

Abstract Laser welding is used in critical component production when tight tolerances like minimal distortions and residual stresses are required. beam offers a lower heat input, smaller affected zone, stresses, minimum distortions, greater mechanical joint characteristics than conventional does. In order to simulate the laser process on SS316L plates, Gaussian source model was used. The developed simulated with volumetric APDL coding using ANSYS. thermal profiles at cross sections via...

The anaconda software required python code in order to run the utilized individual K-nearest neighbor (KNN), random forest regression (RFR), and linear (LR) models. results show that RFR machine learning (ML) technique out of other models shows best performance for a used dataset. findings this article indicate dataset proposed model provides an acceptable algorithm FACC design optimization. In current study preparation geopolymer concrete (GPC), relevant variables such as curing, fly ash,...

The electrochemical machining process involves electrical and chemical processes while removing materials from the workpiece. Electrochemical (ECM) lacks accurate models for predicting shape material removal rate during ECM process. This limits ability to optimise predict final product geometry, which is crucial industrial applications. research mainly focused on modelling simulation of workpiece using COMSOL Multiphysics software. developing a mathematical model that describes ECM's...

'This research aims to look at the consequences of diffusion thermo, Hall, ion slip, and radiation absorption on unsteady MHD turbulent rotational flow second-grade fluid through porous materials while also regarding outcomes chemical retort heat absorption. When ratio between number collisions electrons in a cyclotron atoms is large, Hall effects (the parameter) become important. The regular perturbation approach investigates outlines velocity segments, temperature dispersion,...

Dental disease evaluation and clinical assessment are frequently accomplished through radiographic penetration. The difficulty of obtaining an accurate diagnosis from radiographs rises due to the minimal mineral density change in demineralized tissue tooth gum disorders. abnormalities may not be visible on until demineralization is higher than 40%, according literature. As a result, dental practitioner’s judgment can have big impact how accurately radiography penetration depth determined...

Aluminium and aluminium alloy MMCs (AAMMCs) tend to be the most explored materials in MMC development due their broad range of properties such as wear resistance, light weight, strength with durability, improved damping capabilities for automobiles, aerospace, marine at reasonable production costs among other materials. However, reinforcements chosen will have an impact on composite, bridging gap between research problem desired specialised application. In that effort, numerous researchers...

In the present short review of manufacturing techniques metal matrix composites (MMCs), aluminium and magnesium MMCs are reviewed in terms their application properties. Additionally, various elaborated to develop MMCs. It is found that global demand increasing year by due major most industries. The industries based on desired properties end component. can be achieved with shape type reinforcing materials along physical conditions. selection method also an important factor achieve Therefore,...