A5072596598- Advanced ceramic materials synthesis
- Gold and Silver Nanoparticles Synthesis and Applications
- Recycling and utilization of industrial and municipal waste in materials production
- Glass properties and applications
- Hydrogen embrittlement and corrosion behaviors in metals
- Natural Fiber Reinforced Composites
- Manufacturing Process and Optimization
- Material Science and Thermodynamics
- High Temperature Alloys and Creep
- Spectroscopy Techniques in Biomedical and Chemical Research
- Occupational Health and Safety in Workplaces
- Pigment Synthesis and Properties
- Quality and Supply Management
- Biosensors and Analytical Detection
- Engineering Technology and Methodologies
- Multidisciplinary Research Papers Compilation
- Advanced machining processes and optimization
- Material Properties and Failure Mechanisms
- Fiber-reinforced polymer composites
- Mechanical Behavior of Composites
- Advanced materials and composites
- Quality and Management Systems
- Magnesium Oxide Properties and Applications
- Metal Alloys Wear and Properties
- Quantum Dots Synthesis And Properties
Universidad Autónoma de Ciudad Juárez
2016-2023
Centro de Investigación en Materiales Avanzados
2017-2019
This paper presents an analysis and mathematical modeling of the cutting parameters in turning process 1018 steel material. For this analysis, experiment was designed using 40 specimens 1" diameter by 6" long. In experiment, control were speed revolutions per minute (rpm), feed rate inches (inches/minute) depth cut (inches), while response variable is surface roughness micro (µinches). The results show that rate, interaction between affect workpiece. Finally, with RStudio software, a model...
Surface-enhanced Raman scattering (SERS) is a powerful tool with high potential for detection of dilute analytes. Nanofibers functionalized by metal nanostructures and particles are exploited as effective flexible substrates SERS analysis. SERS-active silice-titania-silver (SiO2-TiO2-Ag) nanofibers were prepared using simple approach involving electrospinning. We report method quantitative analysis SiO2-TiO2-Ag the substrate. Precursors SiO2 TiO2 synthetized through sol-gel then incorporated...
The cordierite is one of the most important phases within MgO-Al2O3-SiO2 (MAS) system. In this study, crystallization and microstructure was analyzed. Four samples were prepared, which subjected to a thermal treatment at temperature 1200 °C with permanence time 2 h. selected depending on critical working temperature, specific applications such as coatings glass ceramic materials, according literature review. Characterization performed by analysis, X-ray diffraction, scanning electron...
The corrosion fatigue behavior of a martensitic stainless steel AISI 410 with 12% Cr, used in the fabrication steam turbine blades at low pressure (L-P), was studied using electrochemical noise technique (EN) under mechanical (immersion and aired) conditions. tests were done simulated environment four levels stress (Δσ) 3 wt.% NaCl solution 90 °C. specimens underwent pitting when exposed to corrosive environment; afterwards, such pits generated strength sites over metallic surface,...
In glass-ceramic design, the two most crucial factors are composition and microstructure both control ability to form a glass determines its degree of workability. The also whether internal or surface nucleation can be achieved. If is desired, as case in hot forming glassware, right nucleating agents melted into part bulk composition. For this reason, research work focuses on obtaining cordierite starting from parent MgO–Al2O3–SiO2–MoO3 system, using NiO, ZrO2 TiO2 range 1%Wt 3%Wt, with...
Stitched filaments are known to modify the mechanical properties of glass-fiber-reinforced polymers 2D (GFRPs 2D), so studying effect on is underway determine critical variables involved. This research focuses study tensile strength stitched low-density Barkley FBA BGQS15-15 nylon monofilament biaxial E-Glass Saertex 830 g/m2 (+/−45°) cured with Polyester Sypol Resin 8086 CCP using a vacuum infusion process. Four specimens were made longitudinal distances between reinforcements 0.5, 1.0,...