A5047931073- Aluminum Alloy Microstructure Properties
- Advanced Photocatalysis Techniques
- Microfluidic and Bio-sensing Technologies
- Microfluidic and Capillary Electrophoresis Applications
- Aluminum Alloys Composites Properties
- TiO2 Photocatalysis and Solar Cells
- Metal Forming Simulation Techniques
- Microstructure and mechanical properties
- Electrohydrodynamics and Fluid Dynamics
- Pigment Synthesis and Properties
- Tribology and Lubrication Engineering
- Metallurgical Processes and Thermodynamics
- Gas Sensing Nanomaterials and Sensors
- Innovative concrete reinforcement materials
- 3D Surveying and Cultural Heritage
- Advanced Welding Techniques Analysis
- Nanopore and Nanochannel Transport Studies
- Thermodynamic and Structural Properties of Metals and Alloys
- Innovations in Concrete and Construction Materials
- Metallurgy and Material Forming
Wuhan University of Technology
2023-2024
University of Science and Technology Beijing
2004-2023
Shanghai Construction Group (China)
2021
Mixing of reagents in microfluidics is critical, and currently, the focus on Newtonian fluids, but these are often viscoelastic fluids. In this study, a micromixer containing conductive cylinder proposed based principle induced charge electro-osmosis (ICEO). The Oldroyd-B constitutive model was chosen to characterize flow properties Poisson–Boltzmann used describe ion distribution electrolyte. impact elasticity number (El) fluids mixing efficiency, velocity, vortex studied. results show that...
Micromixers have important applications in lab-on-a-chip, biomanufacturing, and chemical engineering. In this study, a micromixer with conductive barrier plate based on the induced charge electro-osmosis is proposed. The Oldroyd-B constitutive model was chosen to characterize flow characteristics of viscoelastic fluids, Poisson–Boltzmann used electrokinetic properties. effects installation plate, concentration polymer, shape mixing were studied finite volume method. efficiency fluids 78.3%...
We investigated the phenomenon of induced charge electro-osmotic flow (ICEOF) driven by a cylindrical electrode in container, focusing on characteristics under different electric field conditions. Through analytical derivation, we provided approximate expressions for zeta potential and slip velocity around surface direct current rotating fields (ROT), as well presence an alternating effect transistor. The study primarily analyzes distribution influence ROT field, validity derived formulas...
Measurement and calculation of surface tension undercooled liquid Fe-20 wt.% Cu alloyUsing electromagnetic levitation in combination with the oscillating drop technique, alloy above below liquidus temperature was measured.The containerless state during produces substantial undercooling up to 156 K.In experimentally covered range, determined as 1.658 -2.234610 -4 (T -1736) N/m.According Butler's equation STCBE software, also calculated.A good agreement found between calculated measured values...
Yellow colored anatase Fe/N co-doped TiO 2 powders have been successfully synthesized by one step hydrothermal method at a lower temperature. The grain size was about 10 nm and the specific surface area of ranged from 160 to 166 m /g. light absorption enhanced in visible region 400~500 new peak 470 appeared when Fe/Ti ratio exceeded 0.5%. photoactivity has greatly improved than that un-doped under irradiation.
In this study, carbon nanotube(CNT) reinforced Al-Cu-Mg composites were fabricated by high energy ball milling(HEBM) combined with semi-solid stirring casting technology(SSC). The effect of CNTs on the microstructural evolution and performance enhancement hot extruded CNT/Al-Cu-Mg was investigated. It indicates that can significantly refine α-Al phase in composite change its grain orientation.The hot-extruded had an inhomogeneous microstructure composed coarse grained zones less fine rich...
TiO 2 thin films were prepared on SiO -coated glass substrates using sols deriving from high concentration titanyl sulfate solution by the spin-coating technique. The calcined characterized X-ray diffraction, UV-Vis spectroscopy, scanning electron microscopy. film exhibited transmittance in visible light region and absorption ultraviolet region. contact angle of /TiO decreased to below 5° under 30 min UV irradiation can sustain for 1 weeks.
Micron-sized silicon carbide(SiC) particles and or Carbon nanotubes(CNTs) were reinforced with Al-Si-Cu-Mg alloy via semi-solid stirring casting technology(SSC). The mechanical properties, microstructural evolution deformation mechanisms under SiC/CNTs either individually in aggregate form conditions investigated by uniaxial tensile tests characterizations. results revealed that can significantly refine the α-Al phase composite change its grain orientation. of EBSD TEM showed after dynamic...
In this study, CNTs reinforced Al-Cu-Mg-Si nanocomposites were successfully facbricated by high-energy ball milling(HEBM) combined with semi-solid stir casting. Then the composites subjected to hot extrusion. The Microstructure and Phase analysis of CNT/Al-Cu-Mg-Si characterized Optical microscope, Scanning Electron Microscope(SEM) XRD. Also density, hardness wear measured. results show that addition effectively inhibited growth α-Al grains, grains obviously refined. addition, dynamic...
Abstract The influence of different ceramsite pre-wetting time and the floating beads content on properties lightweight high-strength concrete was studied in this paper. results showed that as increased, absorption rate continued to increase, reaching a saturated state at 12 h with 36.14% water rate; slump/expansion degree is increased significantly, growth decreased gradually, improvement not obvious after h; 7 d strength saw an downturn, dropped by 10.4% h, which decline basically stable;...