is present project investigated the impact penetration response of woven jute fiber reinforced composites subjected to wide range low velocities. Hand layout fibers are thermally compressed ensure no internal defects formed in composites. Six layers jutes stacked together using different orientations [0/q/0] s . Low velocities used ranging between 5 – 20 m/s. Force-time, force-displacement and energy-time curves obtained automatically during tests. The results then discussed with considering...

This study is an approach to investigate the environmental impact of screw manufacturing and choose suitable material for selected screw-making processes best performance with minimum impact. The parameters involved were types process using data available in Asia region. two different approaches being evaluated machining forging. considered low carbon steel, stainless titanium alloy aluminium alloy. As process, materials alloy, magnesium cast iron. information are generated by SolidWorks....

In the last years, there is an increasing acknowledgment of our impact on environment due to lifestyle, while need adopt a more sustainable approach as consumption habits emerges particular significance. This trend regards industrial sectors affecting and, especially, electronic industry where short life cycles and rapidly developing technology have led increased e-waste volumes, such discarded equipment. Waste Electric Electronic Product or E-waste referred all kind electric equipments...

Both TQM and Innovation are the competitive key factors that intensely embedded into organizational products, service process. In order to achieve higher business performance, organizations needed adopt both quality innovation. Therefore, main objective of this paper is identify relationship between performance with a mediator's effect Innovation. After detailed review extensive literature, new model presented. The proposed integrates practices different type innovation attempt develop...

The serial batch leaching test of an electronic arc furnace oxidizing slag was performed on the basis JIS K 0058-1 to investigate safety and clarify elution mechanism. which discharged at time refining normal steel used for this experiment. dissolved in water whose initial pH 6.0. After that, naturally dried. This operation 12 times successively.The dissolution behaviors Ca Mg were expressed by parabolic law. That Si linear dissolutions them from controlled diffusion through pore surface...

Sustainability issues will provide impact on the environment, social and economy. The importance of these three aspects sustainability must be look at in tandem. Some pillars getting more attention by companies since they are interested to identify that may affect performances related their people or profit. Through CSRs report released various international companies, this paper identified value which place for economic sustainability. Result shows human right and, occupational safety have...

Southeast Asia is a standout amongst the most presented districts to unnatural weather change dangers even they are not principle worldwide carbon dioxide (CO2) maker, its discharge will get be significant if there no move made. CO2 wellsprings of mainly by fossil fuel through era power and warmth generation, also transportation part. The endeavors taken these nations can ordered into administrative local level. This paper review potential for catch capacity (CCS) as part environmental...

Metal oxide semiconductor material has great potential to act as window layer in p–n heterojunction solar cell thin film owing low production cost and significant properties photovoltaic mechanism. In this work, n-TiO2/ZnO bilayer was effectively constructed by means of sol-gel spin coating technique an effort diminish the electron-hole recombination rate from single-layered film. Annealing time is one important parameters fabrication process varied study impact annealing treatment towards...

Small and Medium Enterprises (SMEs) industry plays important role in economic growth Malaysia especially food production industries. Ergonomics SMEs industries are one of the most common issues being neglected among people. In this study, objective is to identify possibility an adverse health effect, conduct hazard risk assessment lastly evaluate ergonomics problem at SMEs. Hazards identification was done through interview sessions Industrial Accidental Prevention Association (IAPA)...

This experiment is about fabrication of n-type Cu 2 O thin film on fluorine doped oxide (FTO) glass by using copper acetate based solution through potentiostaticelectrodeposition. A range deposition time was carried out from 20 to 40 minutes and the results were obtained. The other parameters such as potential deposition, bath temperature pH value kept constant for-0.125Vvs Ag/AgCl, 60 °C 6.3, respectively. It found that optimum for growth mechanism 30 minutes. Structural, morphologicaland...

In the preparation of triaxial porcelain from Palm Oil Fuel Ash (POFA), a new parameter variable must be determined. The parameters involved are particle size POFA, percentage POFA in composition, moulding pressure, sintering temperature and soaking time. Meanwhile, shrinkage is dependent variable. optimization process was investigated using hybrid Taguchi design flower pollination algorithm (FPA). interaction model derived regression analysis found that highly on followed by between time...

In order to solve the electromagnetic interference (EMI) issue and provide a new application for palm oil fuel ash (POFA), POFA was used as cement filler enhancing EMI absorption of cement-based composites. refined by using water precipitation 24 hours remove filthiness distinguish layer 1 (floated) 2 (sink) POFA. Both layers were dried at 100 ± 5 °C grind separately sieve 140 μm (Fine) 45 цш sizes (Ultrafine). The micro structure element content both characterized scanning electron...

The serial batch leaching test of an electronic arc furnace oxidizing slag was performed on the basis JIS K 0058-1 to investigate safety and clarify elution mechanism. which discharged at time refining normal steel used for this experiment. dissolved in water whose initial pH 6.0. After that, naturally dried. This operation 12 times successively.The dissolution behaviors Ca Mg were expressed by parabolic law. That Si linear dissolutions them from controlled diffusion through pore surface...

A fundamental study was carried out in order to fix CO2 on slag. The electronic arc furnace reducing slag wet-ground by a vibration ball mill under atmosphere. effect of grinding conditions the behavior absorption investigated.The rate wet larger than that dry grinding. total amount increased with increase and water case weight ratio kept constant. fixed as CaCO3 Ca4Si2O6(CO3)(OH, F)2. Any compounds Mg were not detected XRD after experiment. In early stage grinding, absorbed even if stopped....

Nowadays, lean practices are implemented in many manufacturing and services companies. Lean order to minimize wastes while maximise the overall performances an organisation. In service sector, importance ensure value added can be delivered customers. However, Malaysia automotive companies cannot compete with Japanese terms of their customer satisfaction. The purpose this study is compare practice between centres. A total 80 questionnaires out 100 distributed were responded represented as 80%...

This paper presented a numerical solution of stress intensity factors (SIF) for slanted cracks in round bar subjected to mode I loading. According the literature survey, most SIFs were extracted from perpendicular and behaviors such well understood. However, difficult obtain. Therefore, it is crucial task solve these problems related with cracks. Three important parameters used as crack aspect ratio, a/b, relative depth, a/D angle, θ. It found that played an role determining where if a/b...

The instability in today's market and the ever increasing emerging demands for mass customized hybrid products by customers, are driving companies decision makers to seek cost effective time efficient improvements their product development process. Design concept evaluation which is end of conceptual design one most critical points development. It relates final success development, because poor criteria assessment can rarely compensated at later stages. This has led real pressure adaptation...

Abstract Sustainability assessment is recognized as a powerful and important tool to measure the performance of sustainability in company or industry. There are various initiatives exists on tools for sustainable development. However, most measurement emphasize environmental, economy governance aspects. Some companies also implement different indicators evaluate economy, social environmental separately. In this research, new methodology assessing context Malaysian industry has been developed...