A5100440051- Additive Manufacturing and 3D Printing Technologies
- Advancements in Battery Materials
- Advanced Battery Technologies Research
- Tribology and Wear Analysis
- Brake Systems and Friction Analysis
- Advanced materials and composites
- Advanced Battery Materials and Technologies
- biodegradable polymer synthesis and properties
- Polymer composites and self-healing
- 3D Printing in Biomedical Research
- Electromagnetic Effects on Materials
- Fatigue and fracture mechanics
- Additive Manufacturing Materials and Processes
- Innovations in Concrete and Construction Materials
- Epoxy Resin Curing Processes
- Material Properties and Applications
- Vehicle Dynamics and Control Systems
- Manufacturing Process and Optimization
- Flame retardant materials and properties
- Advanced ceramic materials synthesis
- Metal and Thin Film Mechanics
- Electrical Contact Performance and Analysis
- Bone Tissue Engineering Materials
- Advanced Machining and Optimization Techniques
- Intermetallics and Advanced Alloy Properties
Sichuan University
2014-2023
Jilin University
2023
State Key Laboratory of Automotive Simulation and Control
2023
Stanford University
2023
Xihua University
2023
Soochow University
2022
China Academy of Launch Vehicle Technology
2021
Nanchang Hangkong University
2017
Foton Motors (China)
2016
Wuhan University of Technology
2014
An electronic stability control (ESC) algorithm is proposed for a four in-wheel motor independent-drive electric vehicle (4MIDEV) utilizing driving and regenerative braking torque distribution to improve stability. A judgment controller, an upper level are designed the ESC system. The controller generate desired yaw rate sideslip angle stability, mode, which normal mode or set according driver inputs measurement signal inputs. consists of speed tracking moment wheel-slip controllers...
Brake friction composites based on the combinations of banana fiber-barium sulphate were manufactured and characterized for their physical, mechanical tribological properties. The properties evaluated following IS 2742 norms a Chase machine. experimental outcome reveals that fiber barium have noteworthy impact tribological, physical composites. Specifically, containing 10 wt% 45 content showed highest coefficient friction, least frictional fluctuations with lowest fade-% compared to other...
Fused deposition modeling (FDM) is a typical 3D printing technology and preparation of qualified filaments the basis. In order to prepare polylactic acid (PLA) suitable for personalized FDM printing, this article investigated effect factors such as extrusion temperature screw speed on diameter, surface roughness ultimate tensile stress obtained PLA filaments. The optimal process parameters fabrication were determined. Further, printable performance objects was preliminarily explored.
The global market for Additive Manufacturing (AM) is expected to grow, which may increase the prominence of sustainability aspects in manufacturing process. A growing number AM academics and practitioners have started pay attention environmental societal impacts instead only focusing on its economic aspect. Yet, still not widely adopted, research at nascent stage. This paper aims better understand AM’s sustainable adoption seeks address three questions: what implications are; challenges...
Electromagnetic coupling treatment (EMCT) is a new method to regulate material properties. To investigate the effect of EMCT on plasticity Al-Cu-Mg alloy, software simulation calculation was carried out, and then alloy treated with an electromagnetic field, its mechanical properties were tested at room temperature. The results reveal that sample generates plastic strain 6.88*10 3 ppm, potentially enhancing tensile experimental findings indicate did not have substantial impact strength...
Corn stalk fibre reinforced nonasbestos environment-friendly friction composite materials have been fabricated, and their physical, mechanical, tribological properties are characterized. The of the composites were evaluated following GB5763-2008 norms on a constant-speed-type tester. experimental outcome reveals that content corn has noteworthy impact tribological, physical composites. Specifically, with 7% exhibited excellent wear properties. worn surface morphology was further investigated...
Selective laser melting (SLM) fabrication of lattice structures has attracted considerable interest due to its many immanent advantages, such as high specific strength. A wide variety have been designed and fabricated. However, a vital prerequisite for design optimization, clear relation between the process constraint SLM apparent properties fabricated structure received much less attention. Therefore, this work systematically investigates characterization preformation rod units, which are...
Metallic micro-powder mixed nanoparticles are applied as original materials in additive manufacturing (AM) and powder sintering because of the thermodynamic size effect nanoparticles. Mechanical properties can be improved by using high density powder. The ultrasonic-assisted electrical discharge is a green easily controlled method to generate metallic A new lab-made device was designed experiments were carried out investigate influence focused ultrasonic power on dense degree distribution...
Packaging plastics are called ‘single-use plastics’ because of short lifetime. Among which, the three polyethylene (PE), polypropylene (PP), and terephthalate (PET) take more than 70%. Due to incompatibility, few research has been done on alloy plastics. The aim this study is investigate possibility single-use plastic (SUPA) ternary PE, PP, PET as 3D printing material. Tensile bending tests carried out mechanical properties, photographs scanning electron microscope (SEM) taken for morphology...
Surface residual stress is made on the aero-engine blades by shot peening to improve fatigue life of blades. As service time increases, surface decreasing due thermomechanical relaxation and centrifugal load caused high-speed rotation. Therefore, detection great importance for predicting remaining Up now, efficient non-contact still a challenge. In this paper, an active thermal deformation excitation (ATDE) method proposed. According theory, material positively correlated with stress,...
Download This Paper Open PDF in Browser Add to My Library Share: Permalink Using these links will ensure access this page indefinitely Copy URL DOI
Download This Paper Open PDF in Browser Add to My Library Share: Permalink Using these links will ensure access this page indefinitely Copy URL DOI