A5101588079- Microstructure and Mechanical Properties of Steels
- Hydrogen embrittlement and corrosion behaviors in metals
- Metal Alloys Wear and Properties
- Welding Techniques and Residual Stresses
- Corrosion Behavior and Inhibition
- Titanium Alloys Microstructure and Properties
- Metallurgy and Material Forming
- Microstructure and mechanical properties
- Magnetic Properties and Applications
- High Temperature Alloys and Creep
- Fatigue and fracture mechanics
- Advanced Photocatalysis Techniques
- TiO2 Photocatalysis and Solar Cells
- Advanced Welding Techniques Analysis
- Material Properties and Failure Mechanisms
- Metal Forming Simulation Techniques
- Magnesium Alloys: Properties and Applications
- Pigment Synthesis and Properties
- Geotechnical Engineering and Soil Mechanics
- Material Properties and Processing
- Natural Fiber Reinforced Composites
- Mechanical Behavior of Composites
- Aluminum Alloys Composites Properties
- Additive Manufacturing Materials and Processes
- Intermetallics and Advanced Alloy Properties
AviChina Industry & Technology (China)
2025
Yueyang Changling Equipment Research Institute (China)
2025
Northeastern University
2019-2024
Soochow University
2022-2024
Zhejiang Sci-Tech University
2023-2024
SAIC Motor (China)
2023
Northwest Institute For Non-Ferrous Metal Research
2020-2023
Wuhan University of Science and Technology
2016
Shougang Institute of Technology
2013
National Dong Hwa University
2006
The grafted modification TiO2@SiO2 composite was fabricated by a liquid-phase deposition method with Na2SiO3 and grafting reaction silane coupling agent. First, the prepared, effect of rate silica content on morphology, particle size, dispersibility, pigmentary property composites investigated scanning electron microscopy (SEM), transmission (TEM), Fourier transform infrared (FTIR) spectroscopy, energy-dispersive X-ray spectroscopy (EDX), photoelectron (XPS), ζ-potential. islandlike had good...
To investigate the effect of combined end-and-shaft post-grouting on vertical load-bearing performance bridge-bored piles in Dongting Lake area Hunan, two post-grouted were subjected to bi-directional O-cell and top-down load tests before after grouting, based Wushi Yiyang Expressway project. A comparative analysis was conducted bearing capacity, deformation characteristics, transfer behavior grouting. This study also examined conversion coefficient γ values different soil layers obtained...
Owing to its superior mechanical properties and recyclability, the carbon fabric/polyetheretherketone (CFF/PEEK) composite has seen increasing application in engineering domains. However, studies examining impact of hygrothermal aging on performance remain relatively limited existing literature. To investigate durability environments, this study fabricated CFF/PEEK composites with a fiber volume fraction 55 vol% subjected them equilibrium hygroscopic treatment at 70 °C. The behavior...
Through the idea of replacing Ni with Mn, a shortened process ultra-fast cooling and two-step intercritical annealing for medium-Mn low-Ni steel after rolling was designed. Microstructures were characterized through optical microscopy, electron probe micro analyzer, scanning backscattered diffraction, X-ray diffractometer. Furthermore, effects different temperatures on austenite including content, stability, impact toughness experimental investigated. The microstructures comprised retained...
For the conventional type-II heterojunction photocatalyst, their photocatalytic activity is affected by limited separation efficiency of electron-hole pairs, exquisitely designed photocatalysts are highly prospective materials for inducing charge transfer efficiently. Typically, enhancing pairs in has been a formidable challenge. Here, hollow mesoporous TiO
The difference in transformation mechanisms between the normal and reverse phase medium Mn steel was revealed using thermodynamic kinetic analysis. results indicate that austenite formation during is a fast reaction, significant amount of 46.9 vol% retained obtained after subjected partial reversion at 650 °C × 1 h. At nucleation stage, lath-like structure, dislocations, martensitic packet boundaries, grain boundaries provide high-density sites for formation. critical temperature reduced by...
The constitutive analysis and microstructural characteristics of Ti microalloyed medium‐Mn steel are studied here by hot deformation test in the temperature range 1123–1473 K at strain rates from 0.01 to 10 s −1 based on thermal simulation. Furthermore, effect addition behavior is elucidated. results indicate that fluctuation flow stress, which sensitive conditions, a result dynamic equilibrium between hardening thermally activated work softening. Flow stress equations for low high content...