A5079744694- Mechanical Behavior of Composites
- Shape Memory Alloy Transformations
- Structural Response to Dynamic Loads
- Advanced machining processes and optimization
- Mechanical Engineering and Vibrations Research
- Advanced Surface Polishing Techniques
- Optical measurement and interference techniques
- Transportation Safety and Impact Analysis
- Natural Fiber Reinforced Composites
- Polymer crystallization and properties
- Structural Health Monitoring Techniques
- Smart Materials for Construction
- Injection Molding Process and Properties
- Textile materials and evaluations
- Material Selection and Properties
- Elasticity and Material Modeling
- Structural Analysis of Composite Materials
- Additive Manufacturing and 3D Printing Technologies
- Titanium Alloys Microstructure and Properties
- Manufacturing Process and Optimization
- Aluminum Alloy Microstructure Properties
- Engineering and Information Technology
- Advanced Machining and Optimization Techniques
- Concrete Corrosion and Durability
- Innovative concrete reinforcement materials
Universidad de Málaga
2013-2024
Mondragon University
2006-2009
Piezoresistivity is the most commonly used sensing principle in cement-based smart composites for strain-monitoring applications. Nonetheless, need external electric power to conduct electrical resistivity measurements restricts scalability of this technology, especially when implemented remote structures. To address issue, manuscript thoroughly analyses piezoelectric properties cement doped with reduced graphene oxide (rGO) and evaluates their potential as self-powered strain sensors. do...
Nowadays, localized forming operations, such as incremental processes, are being developed an alternative to conventional machining or techniques. An indentation process is the main action that takes places in these activities, allowing small, deformations. It essential have knowledge of material behavior under punch and transmitted forces achieve correct control entire procedure. This paper presents work carried out with digital image correlation (DIC) technique applied study flow place...
Abstract The effects of processing parameters on the strength fusion bonding interface have been investigated. was generated when an isotactic polypropylene homopolymer injection molded a solid self‐reinforced substrate. measured in shear configuration, and melting behavior substrate studied using differential scanning calorimetry. results show that strong can be achieved correct are chosen. interfacial is largely improved if temperature higher than layer, these specimens failure does not...
The present work shows the material flow analysis in indentation by numerical two dimensional Finite Elements (FEM) method and experimental two-dimensional Digital Image Correlation (DIC) method. To achieve deep without cracking, a ductile material, 99% tin, is used. results obtained from DIC technique depend predominantly on pattern conferred to samples. Due absence of natural pattern, black white spray painting used for greater contrast. stress-strain curve has been introduced Element...
The paper describes an experimental study developed on the AA7075 T651, which is aluminum alloy extensively used in aeronautical industry. This work presents a double approach of investigation where there no literature about previous research. includes analysis results obtained by combination mechanical and chemical actions properties this material. On one hand, combinations relevant milling parameters (feed rate, cutting speed) flat samples (flat specimens have been selected attempting to...
End-of-life tires (ELTs) pose a serious environmental problem today due to their great ability maintain properties and not degrade under extreme conditions or over time. One of the ways reuse this material is subject it recovery process obtain new raw materials that can be used as convenient. This article focuses on nonlinear viscoelastic characterization rubber obtained by Danish company genan®. has developed manufacturing that, via exothermic reactions, gives renewed (in form cylinders,...
Focusing on the application of 3D Digital Image Correlation technique, this work proposes a material flow analysis an indentation process. The study establishes methodology for calibration and implementation image sensing technology deformation measurements. purpose is to continue with validation DIC processes, where deep penetration achieved extensive produced. With technique possible perform accurate measurements in non planar specimens emerging towards exterior tested specimen, which not...
The present paper explores a new concept of hybrid eco-composite by substituting the natural fibre plies with thin wood veneers. composite, named Fibre-Wood Laminate (FWL), is inspired fibre-metal laminate materials. studied FWL configuration consisted single pinewood veneer at each outer layers flax woven fabric reinforced bio-epoxy composite manufactured infusion. Three-point bending results showed that gives highly anisotropic nature to FWL. In best case, grain 0°, stiffness and strength...
Under external impact load, due to the high strain rate at which a shape memory alloy (SMA) is loaded, stress–strain behaviour under conditions differs from that quasi-static loading as consequence of self-heating SMAs loading.