A5101679908- Additive Manufacturing and 3D Printing Technologies
- Advanced Measurement and Metrology Techniques
- Additive Manufacturing Materials and Processes
- Manufacturing Process and Optimization
- Advanced Sensor Technologies Research
- Advanced machining processes and optimization
- Sensor Technology and Measurement Systems
- Scientific Measurement and Uncertainty Evaluation
- Industrial Vision Systems and Defect Detection
- Optical measurement and interference techniques
- Advanced Numerical Analysis Techniques
- Advanced Surface Polishing Techniques
- Welding Techniques and Residual Stresses
- High Entropy Alloys Studies
- Advanced Sensor and Energy Harvesting Materials
- Surface Roughness and Optical Measurements
- Nanofabrication and Lithography Techniques
- Image Processing Techniques and Applications
- Advancements in Photolithography Techniques
- Tribology and Lubrication Engineering
- Electrospun Nanofibers in Biomedical Applications
- Iterative Learning Control Systems
- Advanced Computational Techniques and Applications
- Bone Tissue Engineering Materials
- Nanomaterials and Printing Technologies
Xi'an Jiaotong University
2015-2024
Xinjiang University
2024
Dongguan University of Technology
2019-2023
Hefei University of Technology
2023
Sensitivity of the sensor is great importance in practical applications wearable electronics or smart robotics. In present study, a capacitive enhanced by tilted micropillar array-structured dielectric layer developed. Because micropillars undergo bending deformation rather than compression deformation, distance between electrodes easier to change, even discarding contribution air gap at interface structured and electrode, thus resulting high pressure sensitivity (0.42 kPa-1) very small...
Continuous fiber reinforced polymer composites (CFRPC) have been widely used in the field of automobile, aircraft, and space due to light weight, high specific strength modulus comparison with metal as well alloys. Innovation on 3D printing CFRPCs opened a new era for design fabrication complicated composite structure performance low cost. provided an enabling technology bridge gaps between advanced materials innovative structures. State-of-art has reviewed according correlations materials,...
A linearization method with improved robustness for determining the displacement from sine and cosine signals generated by optical encoders is presented. The proposed scheme based on a ratiometric technique dedicated compensation method. converts sinusoidal into nearly perfectly linear output signal, which determined precisely using simple equation. Under condition of ideal input signals, theoretical analysis shows that converter enables determination non-linearity error below 0.0029 µm...
Electronic interpolation is the key technology for further improving measurement resolution of optical encoders. In this paper, an electronic interpolator based on ratiometric linearization conversion method presented. The proposed converts sinusoidal encoder signals into a nearly perfectly linear output signal through mathematical manipulation that only involves basic operations addition, subtraction, multiplication, and division. Thus, displacement can be precisely determined using simple...
Materials and Methods Polycaprolactone (PCL) polycaprolactone-hydroxyapatite (PCL-HA) scaffolds with 600-μm pore size were fabricated by drop-on-demand printing (DDP) structured porogen method followed injection molding. Specimens special dimensions of 4.2×4.2×5.4 mm 3 6.6×6.6×13.8 designed for compression tensile tests, respectively. The mechanical study was performed on both solid porous PCL PCL-HA samples. effect properties the HA content ratio in composites investigated. Results Porous...
Abstract To explore the effect of process parameters on bead geometry in cold metal transfer wire arc additive manufacturing(CMT-WAAW), response surface optimization method was adopted this paper. According to previous experiments, some were selected as independent variables. They are feed speed(WFS), traveling speed(TS) and substrate temperature(ST). Some geometric welding dependent track width (w), layer height (h), penetration (p), accumulated area (A2), (A1), aspect ratio (B) dilution...
This paper presents the design of an ultra precision positioning system, which consists a coarse stage and fine stage. Two servo motors moving on recirculating ball screw are used to drive three piezo actuators provide nanoscale positioning. The static dynamic performances system formulated for designing micro Based evaluation system's natural frequency, dual sever loop approach is as control mechanism. main noise caused by ambient environment reduced vibration-suppressing table, in...
Abstract The study aimed to evaluate the effectiveness of blood pool and myocardial models made by stereolithography in diagnosis different types congenital heart disease (CHD). Two modeling methods were applied 8 cases, two control groups consisting experts students diagnosed cases using echocardiography with computed tomography, models, models. importance, suitability, simulation degree analyzed. average diagnostic rate before after 3D printing was used 88.75% 95.9% ( P = 0.001) expert...
Scientists and engineers are looking forward to new manufacturing technologies realize the integrated fabrication of macro shape microstructure for components with a short production chain, which can also save materials reduce energy consumption. Additive (AM) technology is pattern character lay-by-lay material deposition. The fabricated in bottom-up way, from points, lines, layers volume, provided capability solve impossible problem micro- macro-structure by using conventional technologies....