A5087561462- Materials Engineering and Processing
- Advanced materials and composites
- Additive Manufacturing and 3D Printing Technologies
- Material Properties and Applications
- Advanced ceramic materials synthesis
- Innovations in Concrete and Construction Materials
- Additive Manufacturing Materials and Processes
- Aluminum Alloys Composites Properties
- Surface Treatment and Coatings
- Mechanical and Thermal Properties Analysis
- Metallurgy and Material Science
- High-Temperature Coating Behaviors
- High Temperature Alloys and Creep
- High Entropy Alloys Studies
- Engineering Technology and Methodologies
- Advancements in Materials Engineering
- Induction Heating and Inverter Technology
- Intermetallics and Advanced Alloy Properties
- Metal Alloys Wear and Properties
- Engine and Fuel Emissions
- Metal and Thin Film Mechanics
- Metallurgical Processes and Thermodynamics
- Thermography and Photoacoustic Techniques
- Aluminum Alloy Microstructure Properties
- Manufacturing Process and Optimization
Lukasiewicz Research Network - Krakow Institute of Technology
2014-2023
Łukasiewicz Research Network
2019-2022
Institute of Advanced Manufacturing Technology
2016-2017
Shenyang Research Institute of Foundry
2016
Instytut Badawczy Leśnictwa
2006-2015
Foundry (United Kingdom)
2014
Abstract This paper discusses technical problems related with casting of titanium alloys in centrifugal vacuum furnaces. The potentials an analysis the process carried out Flow3D software CFD (Computational Fluid Dynamics) were presented. Simulations on a model set, which enables two connecting rods for I.C. engine. Changes mould filling examined three selected spinning velocities arm. ranges metal flow velocity calculated as well pressure after reaching predetermined velocity. results and...
Abstract Trials of cast steel filtration using two types newly-developed foam filters in which carbon was the phase binding ceramic particles have been conducted. In one source flake graphite and coal-tar pitch, while other replaced by a cheaper precursor. The are fired at 1000°C, i.e. much lower temperature than currently applied ZrO 2 -based filters. During trials were subjected to attack flowing metal stream having 1650°C for 30 seconds. Characteristic filters’ properties before after...
Biocompatible porous materials may find use in the manufacture of bone implant components to facilitate bonding prostheses with tissues. The paper presentsa relatively simple method producing a material from Ti6Al4V alloy by high pressure hot isostatic pressing (HIP). process was carried out capsules made superplastic alloy. were filled mixture powdered titanium and carefully selected salt crystals. mixing ratios had been calculated crystal geometry components. experimental verification...
Abstract Extremely intense development of civilization requires from foundry casting technologies very high quality and not expensive castings. In the foundries, there are many treatments that allow increasing final properties produced castings such as refining, modification, heat treatment, etc. One methods by removing inclusions liquid alloy is filtration. The use ceramic-carbon foam filters in filtration process still analysed phenomenon allows improving A modern method research, testing...
Selection of caSting MaterialS for Working PartS MachineS the foreStry SectorThe article was created as a result work TecHMaTsTraTeG 1 program "Modern Material Technologies" part project with acronym iNNoBiolas entitled "development innovative working elements machines in forestry sector and biomass processing based on high-energy surface modification technologies layer cast elements"; agreement No. TecHMaTsTraTeG1/348072/2/NcBr/2017.The discusses procedure selecting casting materials that...
The article presents a novel method that allows measurement of thermal conductivity is based on Stefan-Boltzmann law.The developed can be used to determine ceramic investment casting molds.The methodology for conducting tests material samples presented.Knowledge the value capacity and as function temperature enables computer simulations process cooling solidification liquid metal in mold.
The results of testing the strength properties experimental ceramic materials containing spending moulding sand after initial mechanical reclamation as a material for subsequent layers stucco composition were presented.Tests carried out on spent sands from various foundry technologies, i.e. with furfuryl resin and hydrated sodium silicate.The spent, agglomerated has undergone crushing process.Next, required granular fractions used individual separated.Ceramic samples, in which was substitute...
Opracowanie metody
Abstract This study shown possibilities of Rapid Prototyping techniques (RP) and metal casting simulation software (MCSS), including non inertial reference systems. RP MCSS have been used in order to design produce essential elements for artificial heart. Additionally it has Fused Deposition Modeling (FDM) technique DodJet technology using prototyped rotodynamic pump. MAGMASOFT® allowed verify the cast kit heart valves model. Optical scanner Atos III enabled size verification experimental...