A5008489720- ZnO doping and properties
- Semiconductor materials and devices
- Ga2O3 and related materials
- Composite Structure Analysis and Optimization
- GaN-based semiconductor devices and materials
- Topology Optimization in Engineering
- Thin-Film Transistor Technologies
- Aeroelasticity and Vibration Control
- Mechanical Behavior of Composites
- Phase-change materials and chalcogenides
- Advanced Photocatalysis Techniques
- Semiconductor materials and interfaces
- Gas Sensing Nanomaterials and Sensors
- Advancements in Semiconductor Devices and Circuit Design
- Structural Analysis of Composite Materials
- Copper Interconnects and Reliability
- Acoustic Wave Resonator Technologies
- Structural Load-Bearing Analysis
- Electronic and Structural Properties of Oxides
- Mechanical stress and fatigue analysis
- Additive Manufacturing and 3D Printing Technologies
- Manufacturing Process and Optimization
- Acoustic Wave Phenomena Research
- Wind Energy Research and Development
- Electrical and Thermal Properties of Materials
Dayeh University
2011-2024
Chang'an University
2018
Materials Science & Engineering
2017
Prince of Wales Hospital
2015
National Yang Ming Chiao Tung University
1995-1999
High-k hafnium oxide (HfO2) film was prepared by high power impulse magnetron sputtering (HiPIMS). The influences of oxygen supply on the plasma state, properties and TFT performance were investigated. films are near-stoichiometric preferentially (−1 1 1)-orientated. When increased from 1% to 3%, excitation/ionization rate species increased, leading higher crystallinity, density lower vacancy defect concentration film, therefore improving dielectric film. further 5%, decreased thereby led...
The development of silicon wafers in the photovoltaic industry towards larger and thinner sizes requires ultrafine tungsten wires, uniform coating high-performance graphite emulsion is key to ensuring quality wires. However, existing mainly depends on imports, limited domestic self-made lotion shows poor dispersion stability nonuniform surface coating. This study provides a strategy enhance rheological property by introducing carboxymethyl cellulose (CMC). with 1.0% CMC addition has best...
High-performance P-type cuprous oxide (Cu2O) film was prepared at room temperature by high power impulse magnetron sputtering. Optical emission spectra revealed that the ratio of Cu radicals/ions in plasma significantly decreased with increasing process pressure due to reduction sputtering yield as target surface oxidized increased oxygen radicals/ions. In addition, increase self-sputtering for cations reduced arrival species substrate surface. As a result, crystal phase transformed from...
It is usually difficult to realize high mobility together with a low threshold voltage and good stability for amorphous oxide thin-film transistors (TFTs). In addition, fabrication temperature preferred in terms of enhancing compatibility the back end line device. this study, α-IGZO TFTs were prepared by high-power impulse magnetron sputtering (HiPIMS) at room temperature. The channel was under two-step deposition pressure process modulate its electrical properties. X-ray photoelectron...
In this article, the tunable Zn-doped Ga2O3 films were obtained by introducing ZnO intercalation during film deposition using plasma-enhanced atomic layer (PEALD). The effect of cycle ratio on performance solar-blind photodetectors (PDs) was first analyzed. Compared to pure Ga2O3, an obviously enhanced PDs observed introduction Zn dopants, especially photocurrent or responsivity, even if light intensity is low. A high sensitivity PD has been achieved with superior photoelectric...
The high temperature in asphalt pavement during summer accelerates the rutting and aggravates phenomenon of urban heat island (UHI). One mitigation methods is use heat-reflective coating (HRC) on pavement. However, conventional HRC faces some challenges such as poor abrasion resistance, skid resistance environment pollution. In this paper, a new type coating, named thermosetting powder (TPC), was developed for reflecting off Four types TPCs, including polyester (PPC), modified (MPPC),...
The research was to develop a small blade fatigue test system which met the criterion of IEC (TR 61400-23) for composite wind turbine blades (SCWTBs). machine consisted servo motor, linear guide, transmission, controlling and clamping apparatuses. These components were used balance weights loaded on blades. Weights added change different mass at each saddle loading tests. Amplitude can be manipulated by rotating eccentric holes flywheel. kinetic power SCWTBs translated from circular motion...
The off-axis sputtering technique was used to deposit Al-doped ZnO (AZO) films on glass substrates at room temperature. For the illustration of sample position in chamber, value of<mml:math xmlns:mml="http://www.w3.org/1998/Math/MathML" id="M1"><mml:mi>R</mml:mi><mml:mo>/</mml:mo><mml:mi>r</mml:mi></mml:math>is introduced. Here,<mml:math id="M2"><mml:mrow><mml:mi>r</mml:mi></mml:mrow></mml:math>is radius AZO target and R is distance between center substrate holder. A systematic study for...
The RF-sputtered β-Ga2O3 films prepared on sapphire substrates were treated by rapid thermal annealing (RTA) with an ultrafast processing time of 30 s. effects RTA at different process temperatures from 600 to 800 °C the researched. Meanwhile, schematic diagram for RTA-induced lattice expansion was proposed. experimental results showed that variation Ga oxidation states and oxygen demonstrated, revealing a greater value 700 °C. (-201) orientation Ga2O3 is observed °C, where (111)...
Aluminum nitride (AlN) film is a promising material which used in various fields. In this study, AlN films with different plasma powers were grown by remote atomic layer deposition. Saturation experiments have been applied the power between 1000 and 3000 W. The influence of on preferential orientation, chemical, optical, electrical properties are investigated. displayed multiphase hexagonal wurtzite crystal structure (002) orientation for higher power, while predominant shifted toward (100)...
The minimum weight design of laminated composite plates subject to strength and side constraints is studied via a constrained global optimization technique. first-ply failure load that treated as the plate determined by using shear deformable finite element one several commonly used phenomenological criteria. optimal layer group parameters (fiber angles thicknesses groups) are proposed technique for attaining satisfying imposed constraints. A number examples symmetrically with various aspect...
The present fatigue life analysis of the small composite sandwich wind turbine blades (SCSWTBs) can be certified by IEC 61400-2:Wind Turbines - Part2: Design requirements turbines (IEC 61400-2 2006). paper will establish an analytical method for SCSWTBs. Microsoft Office EXCEL is used to calculate maximum stress, minimum and stress ratio SCSWTBs under loading. With above data, Goodman diagram (GD) constructed Autodesk AutoCAD. Finally, we easilyestimate