A5102005713- Soil Mechanics and Vehicle Dynamics
- Advanced Algorithms and Applications
- Machine Fault Diagnosis Techniques
- Gear and Bearing Dynamics Analysis
- Agricultural Engineering and Mechanization
- Advanced Sensor and Control Systems
- Industrial Technology and Control Systems
- Structural Engineering and Vibration Analysis
- Wind Energy Research and Development
- Simulation and Modeling Applications
- Solid State Laser Technologies
- Photorefractive and Nonlinear Optics
- Geotechnical Engineering and Underground Structures
- Magnetic and Electromagnetic Effects
- Geomechanics and Mining Engineering
- Structural Health Monitoring Techniques
- Laser Design and Applications
- Power Systems and Renewable Energy
- Embedded Systems and FPGA Design
- Wind and Air Flow Studies
- Advanced Manufacturing and Logistics Optimization
- Hydraulic and Pneumatic Systems
- Scheduling and Optimization Algorithms
- High-Voltage Power Transmission Systems
- Industrial Automation and Control Systems
Jiangsu University
2010-2025
China State Construction Engineering (China)
2024
Zhejiang Province Institute of Architectural Design and Research
2024
China Jiliang University
2023
Shanghai Jiao Tong University
2004-2022
Hangzhou Dianzi University
2022
Chongqing University
2005-2021
Shanghai Polytechnic University
2011-2021
Naval University of Engineering
2021
Chinese Academy of Agricultural Mechanization Sciences
2021
In this paper, a model-predictive control of medium voltage, grid-tied four-level diode-clamped inverter for use in high-power wind energy conversion systems is presented. The objectives such as regulation net dc-link reactive power generation to meet the grid operator request, capacitor voltages balancing, and switching frequency minimization are included cost function. latter objective an important requirement converters, has been achieved without any modifications software or hardware...
Due to the nonlinear and time-varying uncertainties commonly present in practical industrial systems, traditional PID controllers often fail achieve optimal control performance under significant input variations. This paper proposes a gain-enhanced method optimized by generalized Boolean algebra, applying algebraic logic strategies improve parameter adaptability real-time performance. Using MATLAB/Simulink simulation tools, dual-loop model is established for Stewart platform, incorporating...
To address the high efficiency and precision seeding requirements for rice factory seedling cultivation, a whole tray air-suction dual-station cultivation assembly line was designed. Based on whole-tray principle, study focused design of dual-suction seed hole-to-hole device, transverse conveying an automatic replenishment device. Nan Jing 46, 5055, Koshihikari seeds were used performance experiments line. The impact workstation configuration production empty hole rate, reseeding damage...
In recent years, sites with low annual average wind speeds have begun to be considered for the development of new farms. The majority design methods a turbine operating at speed is increase blade length or hub height compared in high sites. cost rotor and tower considerable portion overall cost. This study investigates method trade-off during optimization speeds. A scaling model implemented evaluate energy. procedure optimizes blades’ aero-structural performance considering simultaneously....
Unmanned aerial vehicles (UAVs)-enabled base stations (BSs) can boost the system performance of terrestrial networks with device-to-device (D2D) communication in scenarios that fixed BSs ground are not available. However, serious interference among UAVs and multiple D2D pairs is more challenging than case because changing topology frequently over time. In this paper, power control optimization investigated for communications underlaying UAV-assisted access systems, where a UAV-enabled BS...
This article explores the use of network-connected unmanned aerial vehicle (UAV) communications as a compelling solution to achieve high-rate information transmission and support ultra-reliable UAV remote command control. We first discuss cases UAVs resulting communication requirements, accompanied with flexible architecture for communications. Then, signal interference characteristics are theoretically analyzed, subsequently we highlight design optimization considerations, including antenna...
Machinery condition monitoring and fault diagnosis are essential for early detection of equipment malfunctions or failures, which insure productivity, quality, safety in the manufacturing process. This paper aims at extracting features rolling element bearings incipient stage. K-singular value decomposition (K-SVD), one technique sparse representation signals, is used study. In K-SVD, its dictionary trained from data by machine learning techniques, allows more flexibility to adapt variation...
<abstract> <b><i>Abstract. </i></b> Combine harvesters are not only used for threshing crops but also separating, cleaning, and storing grains. Additionally, they have different forward speeds when crop conditions vary. It is important to adjust optimize the control strategy these machines adapt varying conditions, such as variety, cropping intensity, cutting width. Previous studies provided considerable knowledge about working principles of operation systems combine based on operator's...
The next generation wireless network (NGWN) is envisioned as convergence of heterogeneous networks. vertical handoff plays an important role in supporting the service continuity and guaranteeing quality (QoS). How to select target becomes vital issue designing algorithm. In this paper, we propose a novel service-adaptive multi-criteria (SMVHO) algorithm formulates selection process multiple attributes decision making (MADM) problem. candidate networks are evaluated by set metrics including...
Pavement performance prediction after maintenance and rehabilitation is important to pavement management. A two-parameter exponential international roughness index (IRI) regression model for thin hot mix asphalt overlay was developed based on information from the U.S. Long Term Performance (LTPP) database. The influence parameters α β, which represent initial IRI as completion shape factor of deterioration curve, were statistically analyzed. results suggested that trends in high-temperature...
The existing imaging flow cytometers for cell detection usually require special optical microscope systems, high-speed cameras, and precision injection pumps, which are not applicable point-of-care (POC) diagnostics. Recently, there some portable systems proposed, however, most of them just miniaturize the part yet still rely on external personal computers to realize system control, image storage, processing, display. To address these challenges, we propose a standalone microfluidic with...