A5100721332- Microstructure and Mechanical Properties of Steels
- Metal Alloys Wear and Properties
- Metallurgy and Material Forming
- High Entropy Alloys Studies
- Hydrogen embrittlement and corrosion behaviors in metals
- Metal and Thin Film Mechanics
- Advanced ceramic materials synthesis
- Microstructure and mechanical properties
- Advanced materials and composites
- High-Temperature Coating Behaviors
- Advanced Welding Techniques Analysis
- Metallurgical Processes and Thermodynamics
- High Temperature Alloys and Creep
- Aluminum Alloys Composites Properties
- Iron and Steelmaking Processes
- Metallic Glasses and Amorphous Alloys
- Lubricants and Their Additives
- Metal Extraction and Bioleaching
- Metal Forming Simulation Techniques
- Aluminum Alloy Microstructure Properties
- Diamond and Carbon-based Materials Research
- Advanced Materials Characterization Techniques
- Surface Treatment and Coatings
- Magnetic Properties and Applications
- Membrane Separation Technologies
Jilin University
2006-2025
University of Shanghai for Science and Technology
2014-2024
Anhui University of Technology
2017-2024
Taiyuan Iron and Steel Group (China)
2024
China Iron and Steel Research Institute Group
2011-2024
State Key Laboratory of Enhanced Oil Recovery
2023
Research Institute of Petroleum Exploration and Development
2023
Central South University
2023
Institute of Geochemistry
2023
Chinese Academy of Sciences
2023
The hot deformation behavior, dynamic recrystallization mechanism and processing maps of Ti-V complex microalloyed high strength steel under temperatures ranging from 840 to 1040 °C strain rates varying 0.01 10 s-1 were studied by using thermal-mechanical simulation (Gleeble-3800), optical microscopy (OM), electron backscatter diffraction (EBSD). true stress-strain curves the investigated obtained different conditions, thermal activation energy was calculated, constitutive equations based on...
The application of polyimide (PI) as an effective sizing agent for carbon fiber (CF) in CF/poly ether ketone (PEEK) composites represents a promising approach. Here, series novel carboxylated waterborne agents with different aliphatic ratios were designed to construct rigid-flexible gradient interphase the purpose promoting interfacial adhesion between CF and PEEK. results indicated that possessed small particle sizes excellent stability, exhibited superior thermal resistance up 400 °C. It...
Perovskite materials have been extensively studied in the field of solar cells, and inorganic perovskites, with their good environmental radiation stability, high defect tolerance, carrier mobility, also great potential for betavoltaic batteries. In this study, we analyze all-inorganic perovskite The metal electrode commonly used cell devices, such as Au, has a large effect on β particle incidence. MWCNTs (multi-walled carbon nanotubes) excellent electrical conductivity, while loose porous...
The microstructural evolution, precipitation behavior, and hardness variation of the Ti-V-Mo complex microalloyed steel during isothermal holding following austenite deformation have been investigated using thermal simulation tester (Gleeble-3800), optical microscope (OM), scanning electron (SEM), backscatter diffraction (EBSD), transmission (TEM), Vickers tester. results indicate that microstructure transforms from to ferrite as time increases 0 s 5400 at 630 °C, with primarily comprising...
Carbon dioxide flooding is a strategic replacement technology for greatly enhancing oil recovery in low-permeability oilfields, which includes social benefits resulting from carbon emission reduction and economic owing to the improvement of recovery. Therefore, it great significance develop apply CO2 storage petroleum industry. In reservoir conditions, usually under supercritical state, presenting both low viscosity high diffusivity gaseous state density liquid state. The special phase...
Designed Fe-0.25C-1.5Mn-1.2Si-1.5Ni-0.05Nb (mass%) hot-rolled plates with different thicknesses are subjected to a novel quenching-partitioning-tempering (Q-P-T) process suitable for engineering water quenching followed by salt bath tempering or air cooling. A passing underwater equipment (PUQE) is specially designed realization of the Q-P-T engineering. The tensile results show that samples exhibit both high yield strength over 900 MPa and elongation 15%. Microstructural characterization...