A5100782259- Aluminum Alloys Composites Properties
- Microstructure and mechanical properties
- Aluminum Alloy Microstructure Properties
- Advanced ceramic materials synthesis
- Advanced materials and composites
- Metallurgy and Material Forming
- Metal and Thin Film Mechanics
- Metal Alloys Wear and Properties
- Titanium Alloys Microstructure and Properties
- Electrical Contact Performance and Analysis
- Metallurgical Processes and Thermodynamics
- Bone Tissue Engineering Materials
- Diamond and Carbon-based Materials Research
- High-Temperature Coating Behaviors
- Mechanical stress and fatigue analysis
- Metallurgy and Material Science
- High Entropy Alloys Studies
- Powder Metallurgy Techniques and Materials
- Electronic Packaging and Soldering Technologies
- Copper Interconnects and Reliability
- High Temperature Alloys and Creep
- Advanced Welding Techniques Analysis
- Additive Manufacturing Materials and Processes
- Ultrasound and Hyperthermia Applications
- Metallic Glasses and Amorphous Alloys
Chongqing Medical University
2012-2025
Xi'an Technological University
2025
China XD Group (China)
2025
Bioscience (China)
2021-2024
University of California, San Diego
2024
University of Shanghai for Science and Technology
2013-2023
Shihezi University
2021
Shanghai Jiao Tong University
2006-2021
PLA Army Service Academy
2018-2021
Central South University
2021
Abstract Copper alloys and copper matrix composites have been attracting a lot of attention lately. Their composition design, preparation, processing directly affect the final performance. In this review, several typical alloys, such as Cu-Fe-P, Cu-Ni-Si, Cu-Cr-Zr are analyzed. The deformation mechanisms, microstructure evolution, dynamic recrystallization behavior summarized. addition, dispersion strengthened graphene reinforced reviewed.
Drugs and biocompatible nanoparticles have raised significant potential in advancing the bone regeneration. Electrospinning technology enables full realization of value drugs nanoparticles.
CuCrZr alloy with good comprehensive properties was prepared by adjusting the process parameters in selective laser melting. The direct aging heat treatment at different temperatures of SLM further improves performance. final experimental results show that increase power and decrease scanning speed, overall performance tends to gradually. With hatching distance, first increases then decreases. After optimization, maximum relative density can reach 97.65% when is 435w, speed 350 mm s−1,...
LiNi0.8Mn0.1Co0.1O2 (NMC811) is a popular cathode material for Li-ion batteries, yet degradation and side reactions at the cathode-electrolyte interface pose significant challenges to their long-term cycling stability. Coating LiNixMnyCo1-x-yO2 (NMC) with refractory materials has been widely used improve stability of interface, but mixed results have reported Al2O3 coatings Ni-rich NMC811 materials. To elucidate role effect coating, we coated commercial-grade electrodes by atomic layer...
Airborne Staphylococcus aureus exists widely in the natural environment and is closely related to human health. Growing evidence indicates that environmental air pollution elevates risk of depressive disorders. However, potential role airborne S. development depression remains unclear. This study aims elucidate neurotoxic effects mechanisms associated with caused by aureus. Mice were randomly divided into four groups, experimental groups at 4.89 × 102, 8.89 105, 1.27 108 CFU/m3 during...
Abstract TiB 2 /7050 composite is a new kind of lightweight and high-strength engineering material. Friction stir welding reliable method for realizing its high-quality connection. In this paper, the friction processing 7075Al dissimilar materials was simulated. The influence parameters on flow field temperature studied. results show that heat input moderate, plastic weld metal sufficient when rotating speed stirring head 1200 r/min traveling 150 mm/min. work can provide important references...
Abstract Hard anodized aluminum oxide coating was prepared on the surface of 6061 alloy by anodizing technology, and effects different voltages structure properties were systematically studied, aiming to prepare high‐quality coatings with excellent wear resistance corrosion resistance. The microstructural analysis tests at showed that under conditions 120 180 V, did not form a complete nanoporous structure, thickness low, performance weak. In contrast, 240, 300 360 V higher thickness,...
The approximate process range for preparing the Cu-Cr-Zr alloy by selective laser melting (SLM) was determined ANSYS simulation, and influence of SLM parameters on comprehensive properties SLM-formed studied design experiments. with optimum strength hardness prepared high efficiency optimizing (i.e., power, scanning speed, hatching distance). It is experimentally shown that tensile are increased increasing power decreasing whereas they initially then decreased distance. Moreover, strength,...