A5005862976- IoT-based Smart Home Systems
- Molecular Junctions and Nanostructures
- Wind Energy Research and Development
- Electrochemical Analysis and Applications
- Embedded Systems and FPGA Design
- Advanced biosensing and bioanalysis techniques
- Energy Load and Power Forecasting
- Embedded Systems Design Techniques
- Wind Turbine Control Systems
- Smart Grid Energy Management
- Electronic Packaging and Soldering Technologies
- Vibration and Dynamic Analysis
- Analytical Chemistry and Sensors
- 2D Materials and Applications
- Acoustic Wave Phenomena Research
- Neural Networks and Applications
- Solar Radiation and Photovoltaics
- Low-power high-performance VLSI design
- Wireless Power Transfer Systems
- Advancements in PLL and VCO Technologies
- Nanowire Synthesis and Applications
- Energy Harvesting in Wireless Networks
- Wind and Air Flow Studies
- Grey System Theory Applications
- Vehicle Noise and Vibration Control
Hospital Universiti Sains Malaysia
2024
Penang Development Corporation
2020-2021
University of Kuala Lumpur
2018-2019
Communications & Power Industries (United States)
2001
Swansea University
1966
Wind turbine is a device that converts kinetic energy of wind into electrical energy. Weak air pressure with an average 2m/s to 4m/s makes implementation in Malaysia becoming difficult and unrealistic. In order produce good power torque, quality needed. performance depends on the incoming speed. Fluctuating low are significant challenges implementation. There many types mechanism control but production output still considered compared actual equipment. large building, Heat Ventilation Air...
<span>This work presents a design and development of remote controller application using an Altera DE2-115 board. A lighting provides smart technologies make it viable to monitor, control support users in which can enhance the quality life promote independent living. Nowadays, turn on electrical devices, user will go located switch. It is difficult required more time switch devices instead staying at certain location while controlling switching mode devices. Implementing this system,...
Currently, digital clock adapts microprocessor or microcontroller system. Performance of speed and reconfigurability issue become a main concern in clocks. New additional feature may be introduced clocks the future. Field programmable gate array (FPGA) offer better performance reconfiguration features. Based on these advantages, it is essential to study explore with FPGA design. The objective this create hardware description language (HDL)- based alarm system implement onto Altera DE2- 115...
This study focuses on the development of electrical power forecasting based electricity usage in Wuzhou, China. To develop a model, important features need to be identified. Therefore, this investigates performance feature selection method, focusing mutual information as filter and random forest wrapper-based selection. From experiment, six have been chosen, whereby both methods chose almost identical features. Later, selected are trained tested with common machine learning models, namely...
on the Altera DE2-115 Trainer Board.The entry of secret code was being designed by creating and length variable.For example, consists four-digit numbers.Therefore,
Cyclic voltammetry electrochemical biosensors reported a wide usage and applications for its fast response, able to be miniaturized sensitivity. However, the bulky, expensive laboratory-based readout circuitry made it impossible used in field-based environment. A portable DNA detection using hybridization technique had been design developed this work. It embedded with fabricated FR4 based sensor produced respective current when applied voltage was within range of 0 0.5 V. The verified five...
This paper describes the development of stand solar panel based on angle and direction. A direction here means photovoltaic is facing sun. 5 different angles had been investigated. The method used in this was an output 50W photovoltaic. as a reference to identify performance PV. 3 places chosen at north Peninsular Malaysia. results show approximate 90° best design for need be inclined by considering other factors. Tilt 87 North Malaysia, which position development. analysis voltage from...
Silicon, glass and ceramic are commonly base substrate used in DNA biosensor fabrication due to its biocompatible, expensive, hard brittle. However the difficulty for drilling dicing, these materials required expensive equipments complex methodology of fabrication. Large gap thermal expansion coefficient (TEC) between silicon/glass film caused microcracks. Hence, aim this work is investigate suitability application a non-biocompatible material, flame retardant 4 (FR4) as label free...
Horizontal Axis Wind Turbine (HAWT) had been widely used in Malaysia, however, research concluded that the power produced is still low which approximately 0.02% from wind turbine input is. The average speed Penang, recorded between 1.0 m/s to 2.5 whereby produce 2.7 kW of by HAWT, 12.0 needed. Therefore, main objective this project develop and analyse suitability on Vertical (VAWT) be for generation with 0.5 3.0 m/s. Ducting system chosen rather than open air since commercial buildings Heat...
Complete gapfill of 0.1 /spl mu/m features with electroless Cu seed layers and electroplated was demonstrated. Electrical tests on test structures indicated similar line via chain resistance, yield line-to-line leakage current wafers PVD filled Cu.
Abstract Glass fabricated with Ti/Au is a common technique for DNA in biosensor application. However, the wet etching produced poor adhesion on glass. FR4 had been investigated to be used as based material this research. Three types of thermal evaporated methods metal fabrication are investigated; Ti/Au, oxidized Cu/Au, and non-oxidized Cu/Au. In research, Ti Cu acts layer Au. A 2 cm length, 1.2 width 1.6 mm thickness was base material. The cleaned sequentially acetone isopropanol then left...