A5100329518- Aluminum Alloys Composites Properties
- Aluminum Alloy Microstructure Properties
- Advanced ceramic materials synthesis
- Advanced materials and composites
- Metallurgy and Material Forming
- Microstructure and mechanical properties
- Intermetallics and Advanced Alloy Properties
- High-Temperature Coating Behaviors
- Titanium Alloys Microstructure and Properties
- Magnesium Alloys: Properties and Applications
- Thermal properties of materials
- Advanced Thermoelectric Materials and Devices
- Bauxite Residue and Utilization
- Thermal Radiation and Cooling Technologies
- Injection Molding Process and Properties
- Nonlinear Optical Materials Research
- Materials Engineering and Processing
- Hand Gesture Recognition Systems
- Machine Fault Diagnosis Techniques
- Advanced Electrical Measurement Techniques
- Metal Alloys Wear and Properties
- Hydrogen Storage and Materials
- Advanced machining processes and optimization
- Educational Technology and Pedagogy
- Turbomachinery Performance and Optimization
Criminal Investigation Police University of China
2024
Inner Mongolia University of Technology
2009-2022
Marine Design & Research Institute of China
2022
Guangzhou Experimental Station
2020
Huizhou University
2020
Hebei University of Technology
2019
Tobacco Research Institute
2014
University of Science and Technology Beijing
2003-2006
Ford Motor Company (France)
2006
University of Puerto Rico-Mayaguez
1995-2002
The microstructure and mechanical properties of Ti-3.5Al-5Mo-6V-3Cr-2Sn-0.5Fe high strength titanium alloy sheets prepared by unidirectional cold rolling two-step cross were investigated. Results showed that the β phase grains refined significantly followed solution treatment for a short time. Compared to rolling, time after could reduce non-uniformity sheets. After aging at 550 °C, anisotropy still existed in rolled sheets, tensile was highest along direction. treatment, process sheet not...
Silicon germanium (SiGe) alloys hold promise for thermoelectric power generation at high temperatures and have been applied in deep-space missions. However, enhancement of the dimensionless figure-of-merit (ZT) is still needed practical civil applications SiGe. In this work, we report high-performance oxide/SiGe bulk composites that were obtained via hot-press sintering mixed powders composed phosphorus (P)-doped SiGe prepared mechanical alloying, using a ball-milling technique La–Nb-doped...
Flexible thermoelectric materials are presented with potential applications in electronic devices and energy conversion due to their convenient preparation, good flexibility, various forms. However, as ductility is rarely observed inorganic semiconductors ceramic insulators, reports on of oxide flexible sparse. Here, we report a new method for the synthesis Na1.4Co2O4 material based bulk materials, which prepared by self-flux painted print paper. Seebeck coefficient power factor obtained...
The Supercritical Carbon Dioxide (SCO2) Brayton cycle has been getting more and attentions all over the world in recent years for its high efficiency compact components. compressor is one of most important components cycle. Different from traditional working fluid, SCO2 a risk condensation at impeller inlet because particular properties near critical point. In order to determine possibility condensation, concept called “Condensation Margin (CM)” suited introduced. It associated with total...
La2O3, Al, and CuO powders were used as raw materials pure copper a matrix; La2O3 was added to an Al–CuO system form new La2O3–Al–CuO reaction system. The matrix composites prepared by in situ synthesis technique the near-melting casting method. products, morphology, size, distribution of observed scanning electron microscopy, energy dispersive spectroscopy, transmission while effect on products microstructure, hardness, conductivity studied. results show that size morphology Al2O3 particles...
This paper addresses the effects of Ce-rich mischmetal on microstructure evolution a 5182 aluminum alloy during annealing and rolling processes. The was added to an as-cast in induction furnace, this followed by homogenized at 450 °C for 24 h operation. mechanical properties’ analysis Al were characterized. results show that could modify microstructure, refine α-Al grains, break network distribution Mg2Si phases, prevent Cr Si atoms from diffusing into Al6(Mn, Fe) phase alloys. elements also...
SUMMARY The filtration and retention characteristics of nicotine, phenol, benzo[a]pyrene (B[a]P), 4-(methylnitrosamino)-1- (3-pyridyl)-1-butanone (NNK), crotonaldehyde, hydrogen cyanide (HCN) ammonia in conventional cellulose acetate fiber filters were investigated. By quantitatively analyzing their contents released mainstream smoke retained filters, efficiencies, taken as the ratio filter content to total yield, determined under both International Organization for Standardization (ISO)...
Herein, SnO2- and ZnO2-doped (1.5 wt.%) composite Cu powder was prepared by mechanical alloying (MA) respectively, both the contact materials of oxide-doped alloys were subsequently obtained canned hot-pressing sintering with hot extrusion combined. Scanning electron microscopy (SEM), laser scanning confocal (LSCM) self-designed electrical breakdown device used for investigating microstructure properties including electric conductivity hardness, especially performance Cu-SnO2 alloy in...
Abstract The in situ particle reinforced Aluminum Matrix Composites were manufactured by using the contact reaction method Al-Ti-C-CuO-La 2 O 3 system and 6063 aluminum alloy. morphology size of products interface structures between Al matrix observed TEM HRTEM. results show that are TiC, Ti 20 La. shape TiC is quadrangular nanosacle. (200) // (111) forms a semi-coherent with matrix. elliptical submicron. It found (112̄0) coherent relationship. (011̄2) (101̄2̄) form non-coherent La square...
In situ reaction was carried out using Cu–Ti–CuO as system and pure copper melt medium. When the temperature is close to melting point of copper, sample obtained by casting near point. The effects parameters, such molar ratio reactants preheating temperature, on in mechanism, well size, shape distribution products structure matrix were studied, so prepare Cu-TiO2 composites with good electrical mechanical properties. results show that can produce rutile titanium dioxide particles smaller...