A5100753853- Adhesion, Friction, and Surface Interactions
- Tribology and Lubrication Engineering
- Gear and Bearing Dynamics Analysis
- Brake Systems and Friction Analysis
- Tribology and Wear Analysis
- Granular flow and fluidized beds
- Lubricants and Their Additives
- Tunneling and Rock Mechanics
- Wastewater Treatment and Nitrogen Removal
- Anaerobic Digestion and Biogas Production
- Electrical Contact Performance and Analysis
- Fluid Dynamics and Mixing
- Fluid Dynamics and Heat Transfer
- Membrane Separation Technologies
- Mechanical stress and fatigue analysis
- Microbial Fuel Cells and Bioremediation
- VLSI and Analog Circuit Testing
- Electromagnetic Launch and Propulsion Technology
- Drilling and Well Engineering
- Heat Transfer Mechanisms
- Integrated Circuits and Semiconductor Failure Analysis
- Arsenic contamination and mitigation
- Biofuel production and bioconversion
- Polymer Nanocomposites and Properties
- Rock Mechanics and Modeling
Hefei University of Technology
2016-2025
Henan Academy of Sciences
2024
Anhui Water Conservancy and Hydropower Survey and Design Institute
2021-2024
Shenhua Group (China)
2023-2024
University of Science and Technology of China
2019-2024
Chinese Academy of Sciences
2019-2024
Central South University
2024
Wuhan University
2023-2024
CAS Key Laboratory of Urban Pollutant Conversion
2019-2024
Zhejiang University
2020-2023
Industrial wastewaters are becoming increasingly associated with extreme conditions such as the presence of refractory compounds and high salinity that adversely affect biomass retention or reduce biological activity. Hence, this study evaluated impact long-term increase to 20 gNa+.L−1 on bioconversion performance microbial community composition in anaerobic membrane bioreactors treating phenolic wastewater. Phenol removal efficiency up 99.9% was achieved at 14 gNa+.L−1. conversion rates 5.1...
Controlled stability of proteins is a highly efficient mechanism to direct diverse processes in plants. A key regulatory system for protein given by the CULLIN-RING E3 ligases (CRLs). In this work, MYB43 identified as novel target CUL4-DDB1-PRL1 (PLEIOTROPIC REGULATORY LOCUS 1)-RING ligase (CRL4PRL1 ligase). Its depends on presence PRL1, WD40-containing functioning substrate receptor CRL4 ligases. Genetic studies have indicated that negative regulator cadmium (Cd) tolerance Arabidopsis...
The 10 000× wear resistance improvement of PTFE by a trace amount nanofillers has been heavily studied in the past decade and attributed to moisture-dependent, mechanochemical formation adherent carboxylate salt-rich transfer films. However, debates still exist on role fillers reduction. Based experimental computational studies selected nanocomposites, we proposed that (1) filler-driven polymer defluorination was first key step mechanochemistry; (2) effective wear-reducing lowered energy...
Abstract The melt‐direct intercalation method was employed to prepare poly(propylene) (PP)–maleic anhydride grafted (PP‐g‐MAH)–organic‐montmorillonite (Org‐MMT) nanocomposites. X‐ray diffractometry (XRD) used investigate the effect, crystallite size, and crystal cell parameter in these composites. Two kinds of maleated PP, with graft efficiencies 0.6 0.9 wt %, two sorts manufacturing processes were nanocomposites then their effects on behavior. results showed that effect enhanced by...
The electrical contact resistance and thermal caused by the actual rough surfaces of parallel groove clamps exist during interactions, which affects heat generation rate conductivity, then accuracy multifield coupling numerical simulation. Thus, first, a mechanical–thermal–electrical model clamp is created based on improved representation interactions. Then, progressive sequential method proposed to improve calculation efficiency coupling. Meanwhile, validity verified temperature measurement...
Abstract In this study, two-step approaches to fabricate periodic microstructures on polyethylene terephthalate (PET) and poly(methyl methacrylate) (PMMA) substrates are presented control the wettability of polymeric surfaces. Micropillar arrays with periods between 1.6 4.6 µm patterned by plate-to-plate hot embossing using chromium stamps structured four-beam Direct Laser Interference Patterning (DLIP). By varying laser parameters, shape, spatial period, structure height laser-induced...