A5103191042- Surface Modification and Superhydrophobicity
- Icing and De-icing Technologies
- Fluid Dynamics and Turbulent Flows
- Advanced Condensed Matter Physics
- Polymer composites and self-healing
- Magnetic and transport properties of perovskites and related materials
- Aerospace Engineering and Energy Systems
- Heat Transfer Mechanisms
- 3D Printing in Biomedical Research
- Bone Tissue Engineering Materials
- Solar Radiation and Photovoltaics
- Nanofabrication and Lithography Techniques
- Arctic and Antarctic ice dynamics
- Epoxy Resin Curing Processes
- Aerodynamics and Acoustics in Jet Flows
- Biomimetic flight and propulsion mechanisms
- Cryospheric studies and observations
- Advancements in Battery Materials
- Aerodynamics and Fluid Dynamics Research
- Thermal Analysis in Power Transmission
- Sports Dynamics and Biomechanics
- Inorganic Chemistry and Materials
- Multiferroics and related materials
- Fluid Dynamics and Heat Transfer
- Guidance and Control Systems
China Aerodynamics Research and Development Center
2023-2024
Shanghai University
2018
Jilin University
1997-2014
Jilin Medical University
2014
Qingdao University of Science and Technology
2012
Bioprinting is a novel technique with wide range of potential uses, including the fabrication functioning tissue constructs for use in biomedical sectors. It revolutionary method high-throughput manufacturing that automates fine control over manufactured structures. Bioink refers to solution biomaterials usually encapsulating cells used bioprinting process; this bioink often encapsulates appropriate cell types. In order create ultimate architecture, should solidify during or shortly after...
In this study, the new findings of a low-concentration saltwater droplet impacting and freezing on an ice surface were presented for first time. A detailed parameter study regarding concentration temperature was carefully performed. Besides, experiments with de-ionized water droplets also carried out to make comparison. The revealed that maximum spreading factors decreased as increased or decreased. When surface, some small protrusions might appear, which different from single pointy tip...
The flow and heat transfer of the oblique impact a droplet on stationary liquid film with various dimensionless thicknesses (01.0–0.5) are investigated experimentally numerically. A superhydrophobic guideway is used to create droplet, which causes subsequent asymmetric crown structure splashing. thermal level set method employed capture deformation warm droplets' cold film. parameter study effect Weber number, angle, thickness geometrical characteristics wall flux carried out. results show...
The hybrid Ice Protection System combining thermoelectric and superhydrophobic coating is efficient benefits from low-energy consumption. In order to explore the application details of coating, this paper investigated sensitivities parameters including range heating power icing environmental parameters. paper, an wind tunnel test was adopted study performance under different conditions, as well influence range, variation on ice protection. results showed that effective only when it covers...
To correctly assess the wind loads on photovoltaic (PV) arrays arranged in mountainous areas, a rigid model manometric tunnel test is used to study pressure distribution law surface of PV arrays, and effects mountain slope module inclination angle modules. The shows that small mountains, front modules subject largest load, which pressure, larger higher pressure; In large (≥45°), load rear largest, this case, suction, smaller greater suction; Based results tests, compared with design existing...
This paper aims to study the impact of rearview mirror shape on aerodynamic performance. Two typical mirrors were selected conduct wind tunnel test, and test result showed that noise rear monitoring point 1 was lower than 2. then conducted simulating computation through computational fluid mechanics (CFD) theory Fluent software, obtained size points two mirrors, static pressure chart, motion pattern turbulent kinetic energy distribution diagram, sequentially analyzed reason for more The...
Aiming at different sub-grid models of large eddy simulation, numerical simulation aerodynamic noise caused by rearview mirror was conducted the simulation. Compared with experimental data, results four on have difference respectively. Studies shown that result using Dynamic Stress Smagorinsky-Lilly model is closest to and other three larger error. Using in for predicting effective feasible, which can be used as reference subsequent wind prediction.
Abstract ChemInform is a weekly Abstracting Service, delivering concise information at glance that was extracted from about 100 leading journals. To access of an article which published elsewhere, please select “Full Text” option. The original trackable via the “References”