A5115588782- Advanced battery technologies research
- Fuel Cells and Related Materials
- Gut microbiota and health
- High voltage insulation and dielectric phenomena
- Spaceflight effects on biology
- Essential Oils and Antimicrobial Activity
- Landslides and related hazards
- High-Temperature Coating Behaviors
- Electronic Packaging and Soldering Technologies
- Rock Mechanics and Modeling
- Conducting polymers and applications
- High Entropy Alloys Studies
- Advanced MIMO Systems Optimization
- Granular flow and fluidized beds
- earthquake and tectonic studies
- Advanced Wireless Communication Techniques
- Earthquake Detection and Analysis
- Reservoir Engineering and Simulation Methods
- Advanced Queuing Theory Analysis
- Spondyloarthritis Studies and Treatments
- Neurofibromatosis and Schwannoma Cases
- Electrostatic Discharge in Electronics
- Calcium Carbonate Crystallization and Inhibition
- Dielectric materials and actuators
- Management of metastatic bone disease
Tongji University
2024-2025
Soochow University
2025
Second Affiliated Hospital & Yuying Children's Hospital of Wenzhou Medical University
2025
Wenzhou Medical University
2025
University of Georgia
2024
China Huadian Corporation (China)
2024
Northwest A&F University
2024
Beijing Institute of Technology
2024
Peking University
2024
Shanghai University of Electric Power
2024
The increasing trend of LEDs die size reduction driven by the demand for high-resolution displays and compact wearable devices, presents significant challenges assembly packaging. Achieving sufficient paste volume maintaining low void rate in solder during mounting on substrate process is crucial high performance LED applications. This paper a novel approach to wafer bumping using printing process. It demonstrates methods used achieve good with via three reflow steps different stencil...
Intervertebral disc degeneration (IVDD) is the main cause of low back pain, pyroptosis a major contributor to various diseases, including IVDD; however, there currently no effective drugs targeting for therapy. In this study, we established model in nucleus pulposus cells (NPCs) vitro and searched inhibitors FDA Medicine Library. High throughput screening study revealed that Pirfenidone (PFD) was most inhibitor among 1500+ drugs, which confirmed by further experiments. As administering PFD...
This study presents the impact dynamic properties and pore structure characteristics of shaft lining concrete after exposure to various water pressure levels durations, which provides guidance for design utilization supporting materials at ingate. The maximum was 0.55 MPa, highest 10 MPa longest duration 14 days. Research found that remained constant, lasted 1 day, strength increased with increasing pressure, whereas exhibited a decreasing trend when longer time. Water unchanged, an as...
Organic photovoltaics (OPVs), representing a novel paradigm in photoelectric conversion technologies, have garnered substantial interest within the renewable energy sector. These leveraging organic molecules or polymers for photon absorption and subsequent electricity generation, stand contrast to traditional silicon-based solar cells. OPVs offer distinct advantages, including flexibility, lightweight construction, cost-effective production, rendering them adaptable across diverse...
Our preliminary study identified dairy cow placenta extract (CPE) as a mixture of peptides with potent antioxidant activity both in vivo and vitro. However, the specific (AOPs) responsible for this were not yet identified. In current study, we employed virtual screening chromatography techniques to isolate two peptides, ANNGKQWAEVF (CP1) QPGLPGPAG (CP2), from CPE. These found be less stable under extreme conditions such high temperature, strong acid, alkali, simulated digestive conditions....
The oil derived from
The mechanical behavior of a partially recrystallized fcc-CoCrFeNiTi0.2 high entropy alloys (HEA) is investigated. Temporal evolutions the morphology, size, and volume fraction nanoscaled L12-(Ni,Co)3Ti precipitates at 800 °C with various aging time were quantitatively evaluated. ultimate tensile strength can be greatly improved to ~1200 MPa, accompanied elongation ~20% after precipitation. temporal exponents for average size number density reasonably conform predictions by PV model. A...
This paper aims to investigate the role of bi-directional shear in mechanical behaviour granular materials and macro-micro relations by conducting experiments discrete element method (DEM) modelling. The consists a static consolidation subsequent under constant vertical stress volume conditions. A side wall node loading is used exert various angles. results show that can significantly influence materials. However, relationship between responses relies on conditions, i.e. or states induced...