A5100718603- Aluminum Alloys Composites Properties
- Aluminum Alloy Microstructure Properties
- Advanced Welding Techniques Analysis
- Microstructure and mechanical properties
- Advanced Battery Materials and Technologies
- Intermetallics and Advanced Alloy Properties
- Advanced materials and composites
- Catalytic Processes in Materials Science
- Advanced Battery Technologies Research
- Catalysis and Oxidation Reactions
- Electrical Contact Performance and Analysis
- High Entropy Alloys Studies
- Catalysis and Hydrodesulfurization Studies
- Tribology and Wear Analysis
- Biofuel production and bioconversion
- Fatigue and fracture mechanics
- Hybrid Renewable Energy Systems
- Advancements in Battery Materials
- Thermal Expansion and Ionic Conductivity
- Titanium Alloys Microstructure and Properties
- Lipid metabolism and disorders
- Anaerobic Digestion and Biogas Production
- Hydrogen Storage and Materials
- Sphingolipid Metabolism and Signaling
- MXene and MAX Phase Materials
Xi'an University of Architecture and Technology
2011-2024
Central South University
2023-2024
Shaanxi University of Chinese Medicine
2024
Shandong University
2003-2016
Ministry of Education of the People's Republic of China
2016
Henan University of Science and Technology
2014
Materials Processing (United States)
2012
Second Artillery General Hospital of Chinese People's Liberation Army
2011
Beijing Vaccum Electronic Research Institute
2011
Hefei University of Technology
2007-2009
Effects of pre-treatment (either pre-deformation or composed pre-aging and prior to aging) on the dislocation morphologies subsequent precipitation, corrosion behaviors, mechanical properties a novel Al-8.26Zn-1.95Mg-1.89Cu-0.08Sc-0.17Zr (wt.%) alloy were investigated. Pre-existing Al3(Sc, Zr) dispersoids can pin dislocations induced by before aging form cells cell walls. As result, bimodal microstructures are formed during process, with coarse precipitates dispersed along walls fine inside...
The d-band center distribution of high entropy alloys can be controlled by selecting appropriate elements, to optimize the adsorption-catalysis-diffusion lithium polysulfide, developing highly active catalysts with bidirectionally catalytic activity.
An excellent battery cooling system is required not only to control the temperature within a reasonable range, but also minimize parasitic power consumption and failure risk. A simplified thermal model for pouch pack with three schemes developed in this work, where heat generation rate calculated by semi‐empirical equation reliability of validated discharge experiments. Finally, an improved phase change materials (PCM)/liquid coupled proposed, its effects are compared traditional liquid...
Pulsed gas metal arc welding of titanium alloy Ti-2Al-Mn to aluminum 1060 using AlSi5 filler was conducted. Microstructures Ti/Al joints with different heat input were investigated. Chemical composition and phase constituent near interface analyzed. Microhardness distribution the weld zone tested. Binary intermetallic TiAl3 precipitations formed in metal, it concluded that morphology precipitation varies variation input. Welding also has a great influence on microstructure interface. With...
Coal gasification slag (CGS) was used for modification and loaded platinum (Pt) to liquid organic hydrogen carrier (LOHC) the first time. The carbon hybrid silica (C@SiO2) prepared by removing metal oxides residue of CGS through acid treatment calcination. C@SiO2 Pt (Pt-C@SiO2) exhibited only a 1.3% decrease in dehydrogenation conversion rate after 30 hours continuous catalytic methylcyclohexane (MCH), even 100 hours, 4.9%. When directly on (Pt-CGS), it showed higher activity...
In this paper, the method of resistance spot welding with cover plate was proposed to weld materials combination metal high and low resistance, such as steel/aluminum, titanium/aluminum, titanium/magnesium, steel/magnesium; technique insert sheet dissimilar resistance.
The start-up and granulation in a lab-scale Anaerobic Sequencing Batch Reactor (ASBR) fed with synthetic glucose wastewater were investigated. Sludge proceeded after 110 days operation was completed approximately 140 days. Scanning electron microscope images showed that filamentous bacteria like Methanosaeta are abundant the granule exhibit uniform structure. growth of can predominate even if acetate concentration is high ASBR. Short observed effluent. tests composition these microorganisms...