A5100627801- Polymer crystallization and properties
- Additive Manufacturing and 3D Printing Technologies
- Polymer Nanocomposites and Properties
- biodegradable polymer synthesis and properties
- Natural Fiber Reinforced Composites
- Polymer Foaming and Composites
- Injection Molding Process and Properties
- Rheology and Fluid Dynamics Studies
- Thermal properties of materials
- Advanced Sensor and Energy Harvesting Materials
- Fiber-reinforced polymer composites
- Advanced battery technologies research
- Manufacturing Process and Optimization
- Mechanical Behavior of Composites
- Tribology and Wear Analysis
- Graphene research and applications
- Dielectric materials and actuators
- Microplastics and Plastic Pollution
- Epoxy Resin Curing Processes
- Conducting polymers and applications
- Material Properties and Applications
- Advanced Combustion Engine Technologies
- Advanced ceramic materials synthesis
- Supercapacitor Materials and Fabrication
- Aluminum Alloys Composites Properties
Sichuan University
2016-2025
Henan Agricultural University
2025
Yancheng Institute of Technology
2024
Hebei University
2002-2024
General Research Institute for Nonferrous Metals (China)
2023-2024
Huazhong University of Science and Technology
2022-2024
Institute of New Materials
2003-2024
Wuhu Hit Robot Technology Research Institute
2024
State Key Laboratory of Nonferrous Metals and Processes
2023-2024
Beijing University of Posts and Telecommunications
2022-2024
Abstract Adding nanofillers to PLA/PCL blends change their surface and interface properties can improve phase morphology. Here the selective localization of CNTs organoclays as third component in blend is studied. It found that clay selectively localized PLA at whereas are mainly PCL interface. With a reduced viscosity ratio matrices, preferred from PLA. The effects different on morphologies In addition, crystallization behavior ternary systems also shows strong dependence nanofillers....
Burgeoning interest in supracolloidal assembly has reached the point at which field can seek so-called intelligent design rather than solely rely on evolution. Emphasizing Janus and triblock particles, this review presents a progress report formulating rules for of interesting structures. We discuss how to building blocks, bearing mind that patchy particles embody not just geometric shape but also chemical shape, determines particle-particle interactions, process be designed proceed...
The rapid printing of 3D parts with desired electrical properties enables numerous applications. Fused deposition modeling (FDM) using conductive thermoplastic composites has been a valuable approach for such fabrication. produced by FDM possess various controllable structural features, but the effects features on remain to be determined. This study investigated these resistivity and anisotropy 3D-printed ABS/CB composites. process parameters FDM, including layer thickness, raster width, air...
Oriented "shish-kebab" structure can enable remarkable mechanical enhancement in polymers. Therefore, the formation mechanism and practical application of this have been extensively studied. However, effect shish-kebab content on properties is still uncertain. Knowledge crucial academic industrial fields but remains elusive because difficult to control. In work, a self-developed multiflow vibrate-injection molding was used produce samples with different shear layer thicknesses. The...
Abstract In this study, we demonstrate that an Mn‐doped ultrathin Ni‐MOF nanosheet array on nickel foam (Mn 0.1 ‐Ni‐MOF/NF) serves as a highly capacitive and stable supercapacitor positive electrode. The Mn ‐Ni‐MOF/NF shows areal capacity of 6.48 C cm −2 (specific : 1178 g −1 ) at 2 mA in 6.0 m KOH, outperforming most reported MOF‐based materials. More importantly, it possesses excellent cycle stability to maintain 80.6 % after 5000 cycles. An asymmetric device utilizing the electrode...
Modulating the reaction reversibility can help escape kinetic traps and effectively regulate morphology of covalent organic frameworks (COFs). However, most current approaches focus primarily on thermodynamic factors with limited research enhancing pathways. Herein, we introduce a novel strategy that combines "freezing–thawing" pretreatment conventional solvothermal synthesis to enhance pathways in COF-366 synthesis. This limits degree monomer polymerization, facilitating structural repairs...
Abstract The morphological feature of microparts evolved during micro‐injection molding may differ from that the macroparts prepared by conventional injection molding, resulting in specific physical properties. In this study, isotactic polypropylene (iPP) with 200 µm thickness and 2000 were prepared, their comparison was investigated means polarized light microscopy (PLM), scanning electron (SEM), differential calorimeter (DSC), wide‐angle X‐ray diffraction (WAXD). results presented some...
Multifunctional smart soft armor materials always among the relentless pursuits of scientists to meet demand extreme environments. In this study, a novel dynamic stab resistance material owned ultraviolet (UV) property constructed with Kevlar fabrics impregnated multi-phase shear thickening fluid (STF) composed SiO2 and TiO2 nanoparticles as disperse phase was fabricated. The rheology test showed that effect displayed stronger concentration in STF (TSTF) increasing. Moreover, compared STF,...
Abstract Thermal wetting can simply, selectively and reversibly join patchy particles into clusters (2D 3D) also colloidal crystals over the narrow temperature range of 1–2 °C. This is demonstrated with Janus (gold half‐coated silica spheres) immersed in a binary mixture water/2,6‐lutidine, such that relative strength gold–gold bonding through hydrophobic interaction silica–silica wetting‐induced attraction switched according to temperature.
As a biobased and biodegradable material that can replace traditional petrochemical-based polymers, poly(l-lactide) (PLLA) shows great application potential. However, its widespread still faces some obstacles, mainly associated with the poor thermal resistance, because molecular chains of PLLA are semirigid regularity. Therefore, crystallization rate is low, making it difficult to crystallize during molding process, finally obtained almost amorphous. In this work, entanglement density was...
Heat dissipation in two-dimensional (2D) material-based electronic devices is a critical issue for their applications. The bottleneck this thermal inefficient heat removal across the van der Waals (vdW) interface between 2D material and its supporting three-dimensional (3D) substrate. In work, we demonstrate that an atomic-scale thin amorphous layer atop substrate surface can remarkably enhance interfacial conductance (ITC) of 2D-MoS2/3D-GaN vdW by factor 4 compared to untreated crystalline...
Abstract Poly(vinyl chloride) (PVC)/SiO 2 nanocomposites were prepared via melt mixture using a twin‐screw mixing method. To improve the dispersion degree of nanoparticles and endow compatibility between polymeric matrix nanosilica, SiO surface was grafted with polymethyl methacrylate (PMMA). The interfacial adhesion enhanced filling resulting PMMA‐ ‐SiO hybrid characterized by scanning electron microscopy. Both storage modulus glass transition temperature measured dynamic mechanical thermal...