A5100429606- High-Temperature Coating Behaviors
- X-ray Diffraction in Crystallography
- Crystallization and Solubility Studies
- Catalytic Processes in Materials Science
- Vehicle emissions and performance
- Electrospun Nanofibers in Biomedical Applications
- Metal and Thin Film Mechanics
- Silk-based biomaterials and applications
- Advanced materials and composites
- Metal Alloys Wear and Properties
- Advanced Combustion Engine Technologies
- Material Properties and Applications
- GaN-based semiconductor devices and materials
- Nuclear materials and radiation effects
- Magnesium Oxide Properties and Applications
- Textile materials and evaluations
- Nuclear Materials and Properties
- Crystallography and molecular interactions
- Layered Double Hydroxides Synthesis and Applications
- Advanced Sensor and Energy Harvesting Materials
- Marine Sponges and Natural Products
- Gas Sensing Nanomaterials and Sensors
- Ubiquitin and proteasome pathways
- Cancer therapeutics and mechanisms
- Smart Materials for Construction
Heilongjiang University of Science and Technology
2019-2023
Xiangtan University
2022-2023
Affiliated Hospital of Hebei University
2022
Harbin Institute of Technology
2012-2017
University of Chinese Academy of Sciences
2017
Wuhan University of Technology
2015-2016
Suzhou Institute of Nano-tech and Nano-bionics
2016
Soochow University
2015
Chongqing Metrology Quality Inspection and Research Institute
2014
Tiangong University
2009
Abstract The application of ultrasonic vibration-assisted cutting in machining is also increasing. In order to provide practical guidelines for industrial applications, a single-factor experimental method was employed compare the surface morphology and roughness 6061 aluminum alloy processed by longitudinal-torsional conventional end milling side milling. influence amplitude on quality systematically analyzed. results indicate that both exhibit similar regular fish-scale-like textures....
This study presents an interesting phenomenon of the simultaneous occurrence adsorption and synthesis Mg–Al layered double hydroxide (Mg–Al– LDH ) by stirring a precursor in aqueous solution with methyl orange ( MO as target adsorbate prepared first milling Mg( OH 2 for 1 h followed another 3 Al( .The samples were characterized set analytical methods including X‐ray diffraction XRD ), thermogravimetry/differential scanning calorimetry TG – DSC Fourier‐transform infrared FT IR ). The maximum...
Response time is the key index of on-line monitoring system. To improve response speed traditional bead thermal conductivity CO 2 sensor, this paper proposes to use multi-walled carbon nanotubes (MWCNTs) performance gas sensor carrier. Nano-sized γ-Al O 3 /CeO powder was synthesized by chemical precipitation method under action ultrasonic wave. SEM morphology reveals a particle size 20–50 nm. MWCNTs were hydroxylated and solution then prepared adding certain amount dispersant The composite...
Abstract To overcome the fragility of chemical cross-linked hydrogel and improve cell compatibility poly( N -isopropylacrylamide) hydrogel, physical cross-linker lithium magnesium silicate hydrate (LMSH) silk sericin (SS) created by Bombyx mori (silkworms) were adopted as biocompatible monomer to prepare SS/poly(NIPAM/LMSH) nanocomposite hydrogels. The temperature sensitivity cytocompatibility like mouse fibroblasts (L929) proliferation desorption investigated. Depending on SS content,...
Potential applications of nanofibers as a new-generation material will be realized if suitable nanofiber yarns become available. Electrospinning has been widely accepted feasible technique for the fabrication continuous yarns. However its low output limited industrial applications. This paper presents new processing approach to fascinated which possess excellent properties while enhancing mechanical strength by core yarn.
AlN thick films were grown on c-plane sapphire substrates by hydride vapor phase epitaxy at high temperature. The evolution of the strain state and crystal quality with increase thickness investigated transmission electron microscopy, field-emission scanning Raman spectra atomic force microscopy (AFM). As increased, stress in epilayers decreased gradually, which was attributed to reaction dislocations first several microns thickness. When more than 20 μm, almost fully relaxed due formation...
Y2O3-ZrO2 thermal barrier coatings on a GH2132 alloy were fabricated by atmospheric plasma spraying method. Failure behaviours of the under combined condition hot corrosion and shock investigated. Surface cross-sectional morphologies before after exposures assessed using scanning electron microscopy. It was established that main failure mode formation net-like cracks in penetrating to bond coat/substrate interface. By detailed consideration analysis X-ray diffraction morphologies, effect...
The Ti/Al/Ni/Au metals were deposited on undoped AlN films by electron beam evaporation. influence of annealing temperature the properties contacts was investigated. When temperatures between 800 and 950 °C, AlN–Ti/Al/Ni/Au became ohmic resistance decreased with increase temperature. A lowest specific 0.379 Ω·cm 2 obtained for sample annealed at °C. In this work, we confirmed that formation mechanism due to Al–Au, Au–Ti Al–Ni alloys, reduction could originate from Au Ti AlAu alloys. This...
The description of the Retraction: Owing to authors' ignorance, a SEM picture (fig.3(d) in this paper) has been used another paper (Fig.3(b) Chinese Journal). After carefully thinking, authors decided withdraw with pity. This decision approved by both Editorial Office JMMR and all authors. We apologize for inconvenience may caused readers. Date July 10, 2023 announcement retraction is available your persual by: https://journals.bilpubgroup.com/index.php/jmmr/article/view/5838
A polymer bubble is easy to be broken under a small external force, various different fragments are formed, which can produced morphologies of products including nanofibers and plate-like strip. Polyvinyl-alcohol/honey solution used in the experiment show hierarchical structure by bubbfil spinning.
This paper introduces a new mixture of peptide derivatives, bearing allyl groups, temporarily named fibroin (AFP), fabricated via reaction low-molecular-weight peptides (FP) with chloride in water/ethanol solvent system. The optimal parameters the preparation were determined through orthogonal analysis experiments. mechanism was investigated, and chemical structure product also confirmed using FT-IR 1H-NMR analyses. results indicated that nucleophilic substitution took place between FP group...