A5101466573- Bone Tissue Engineering Materials
- Copper-based nanomaterials and applications
- biodegradable polymer synthesis and properties
- Electrospun Nanofibers in Biomedical Applications
- Biofuel production and bioconversion
- Advanced materials and composites
- Proteoglycans and glycosaminoglycans research
- Graphene and Nanomaterials Applications
- Electrodeposition and Electroless Coatings
- Advanced ceramic materials synthesis
- Semiconductor materials and interfaces
- Aluminum Alloys Composites Properties
- Quantum Dots Synthesis And Properties
- Cancer, Hypoxia, and Metabolism
- Electronic and Structural Properties of Oxides
- Chalcogenide Semiconductor Thin Films
- Nanoparticle-Based Drug Delivery
- Silk-based biomaterials and applications
- Wound Healing and Treatments
- Anodic Oxide Films and Nanostructures
- ZnO doping and properties
Changzhou University
2023-2025
Xuzhou Medical College
2014
Feng Chia University
2014
Southwest Medical University
2013
First Affiliated Hospital of Sichuan Medical University
2013
Zhengzhou University
2008
This study prepared a composite scaffold composed of curcumin and poly(ε‐caprolactone)‐poly(ethylene glycol)‐poly(ε‐caprolactone) (PCL‐PEG‐PCL, PCEC) copolymer using coelectrospinning technology. Incorporation into the polymeric matrix had an obvious effect on morphology dimension PCEC/curcumin fibers. The results in vitro anti‐oxidant tests cytotoxicity assay demonstrated that curcumin‐loaded PCEC fibrous mats significant efficacy low cytotoxicity. Curcumin could be sustainably released...
Abstract Glass fiber(GF)‐reinforced polymers can cause vigorous wear for the screws and barrels in plasticizing units of injection molding machines. The three types WC composite coatings were selected to spray on 42CrMo steel by high‐velocity oxygen fuel spraying process. designed PPS‐40%GF pins used simulate tribological system. Against pins, rates WC‐12Co, WC‐20Cr 3 C 2 ‐7Ni, WC‐10Co‐4Cr 0.014 × 10 −9 , 0.053× 0.097 mg/mm, respectively. corresponding tribo‐pairs 0.119 0.102 0.079...
Rhenium (Re) thick films were electrodeposited on copper (Cu) substrates with (110) + (311) texture from aqueous solutions additives of 2 g l−1 gelatin, 1 mM sodium lauryl sulfate, and vanillin. The microstructure morphology the different thickness values characterized by scanning electron microscopy atomic force microcopy. chemical composition crystallographic structure identified energy dispersive spectroscopy x-ray diffraction, respectively. Re obtained due to synergistic effect...
Scaffolds for bone tissue engineering applications should have suitable degradability in favor of new ingrowth after implantation into defects. In this study, degradation behavior polyurethane composites composed triblock copolymer poly(caprolactone)-poluronic-poly(caprolactone) (PCL-Pluronic-PCL, PCFC) and nanohydroxyapatite (n-HA) was investigated. The water contact angle absorption were measured to reveal the effect n-HA content on surface wettability swelling n-HA/PCFC composites,...
Large area and uniform nanosheets Co3O4 have been fabricated by thermal annealing of cobalt thin film under the DC magnetron sputtering method. The synthesis is based on controlling simple oxidative formation precursor Co films. films were heated at 300, 400, 500 °C for two hours in a pure oxygen atmosphere. At 300 °C, CoO phases appear to survive together. An amount polycrystalline observed 400 °C. structural morphological properties characterized means transmission electron microscopy...
In this study, large-area and uniform thickness novel nano-sheet structured CuS thin films on ITO glass have been prepared by the one-step electrodeposition method from a dimethyl sulfoxide solution. Thin of completely preserved like morphology CuyS (y = 1.75, 1.8, 1.95, 2.0) are grown vacuum annealing at 500 °C for different lengths time. The sample heated 10 hours was nearly converted to single phase Cu2S with y ∼ 2. optical direct band gaps annealed 2, 6, in were found be 1.94, 1.68, 1.44...
SiCw/3Y-ZrO2/A12O3 composites were prepared. The composite powders prepared by a precursor method. Samples conventionally sintered at 1500°C and 1580°C for 2h in air. density, phases, microstructure, hardness of the investigated. It was found that relative density samples decreased as increasing content SiCw. optimum mechanical properties may be obtained with 5 vol.%