A5082844820- Advanced materials and composites
- High-Temperature Coating Behaviors
- Metal and Thin Film Mechanics
- Erosion and Abrasive Machining
- Electrospun Nanofibers in Biomedical Applications
- Advanced Sensor and Energy Harvesting Materials
- Metal Alloys Wear and Properties
- Conducting polymers and applications
- Natural Fiber Reinforced Composites
- Powder Metallurgy Techniques and Materials
- Advanced Cellulose Research Studies
- Recycling and utilization of industrial and municipal waste in materials production
- Surface Treatment and Residual Stress
- Supercapacitor Materials and Fabrication
- Aerogels and thermal insulation
- Corrosion Behavior and Inhibition
- Polyoxometalates: Synthesis and Applications
- Advanced ceramic materials synthesis
- Aluminum Alloys Composites Properties
- Graphene research and applications
- Dental materials and restorations
- Titanium Alloys Microstructure and Properties
- Pickering emulsions and particle stabilization
- Polymer Foaming and Composites
- Magnetic Properties of Alloys
Inspur (China)
2023-2025
Nanjing Forestry University
2024
Shandong University
2019-2023
Software (Spain)
2023
University of Science and Technology Beijing
2000-2022
State Key Laboratory of Digital Medical Engineering
2019-2021
Southeast University
2019-2021
Ministry of Education of the People's Republic of China
2020
Henan University
2018
Changzhou University
2016
To enhance the erosion resistance of typical Cr3C2-NiCr coatings, Cr3C2-TiC-NiCrCoMo (NCT) coating was developed and deposited by high-velocity oxygen fuel spray (HVOF). The mechanisms were investigated using numerical simulations experimental methods. A comprehensive calculation model for rate developed, incorporating factors such as properties eroded particles, characteristics coating, conditions erosion. NCT calculated predicted model, accuracy these predictions validated through...
A novel honeycomb-like porous composite based on H<sub>3</sub>PMo<sub>12−x</sub>W<sub>x</sub>O<sub>40</sub> and functionalized graphene was fabricated for high-performance aqueous supercapacitors.
p-BC/AgNP carbon aerogels with excellent reabsorption capacities and mechanical properties were prepared by <italic>in situ</italic> reduction carbonization. The had better antibacterial behavior biocompatibility due to their slow controlled release of silver.
Environment‐friendly process, low production cost, and simple operation are regarded as key factors for scalable kesterite photovoltaic applications. Herein a green ammonium thioglycolate (TGAm)‐based aqueous solution route has been developed to deposit Cu 2 ZnSnS 4 films. It is found that sinstering in ambient air good argon, making the process more affordable reproducible. TGAm active than other alkylthiols with longer alkyl chains strong coordination capability toward metal ions, which...
A gas sensor made from graphene vertical field effect transistor (VGr-FET) has been fabricated using as the source electrode, C60 thin film semiconductor layer and aluminum drain electrode. The on/off ratio of gated by bottom electrode with ionic liquid gel dielectric is derived to be 103 measured source-drain current I ds. apparent energy barrier height between polycrystalline fullerene was calculated model heterojunction diode I-V response curves. φ BH altered gating potential vertically...
Abstract α-Ti foil with a protective layer formed on one side was deflected as result of corrosion in methanol (CH3OH) solution containing 0.6 mol/L potassium chloride (KCl) because tensile ...
Despite advances in NiCr + Cr3C2–NiCr coating improving the erosion wear resistance at low impact angles, deterioration medium and high angles has not been solved for impeller subjecting to multi–impact angle. Herein conflict is circumvented by combining performance of under different proposing a novel structure. First, specimens with content were prepared using plasma spraying system. Second, rate coatings relation angle concentration was measured an air jet test system, microhardness on...
The surfaces of nanoparticles SiO 2 , TiO and Al O 3 have been modified by γ-(2,3-epoxypropoxy)propyltrimethoxysilane (KH-560) in order to achieve proper dispersion possible chemical interactions between polymeric coatings, then the homogeneous fluoropolymer coatings containing successfully prepared on mild steel substrates. surface morphologies were characterised field emission scanning electron microscopy. effects incorporating various corrosion resistance fluoropolymer-coated investigated...
To improve the surface corrosion resistance of 42CrMo4 high-strength steel used in a marine environment, this article studied effects hard turning on integrity and through single factor experimental method, namely turning, polarization corrosion, electrochemical impedance spectroscopy, potentiodynamic curve, salt spray tests. The results indicated that was modified by with roughness lower than Ra 0.8 μm, decreased microhardness, fine uniform microstructure, dominant residual compressive...