A5011846088- Combustion and flame dynamics
- Thermochemical Biomass Conversion Processes
- Bone Tissue Engineering Materials
- Heat Transfer and Optimization
- Iron-based superconductors research
- Rare-earth and actinide compounds
- Animal Virus Infections Studies
- Heat Transfer Mechanisms
- Geothermal Energy Systems and Applications
- Membrane Separation and Gas Transport
- biodegradable polymer synthesis and properties
- Radiative Heat Transfer Studies
- Building Energy and Comfort Optimization
- Carbon Dioxide Capture Technologies
- Heat Transfer and Boiling Studies
- Virus-based gene therapy research
- Viral gastroenteritis research and epidemiology
- Phase Change Materials Research
- Physics of Superconductivity and Magnetism
- Additive Manufacturing and 3D Printing Technologies
- Fire dynamics and safety research
- Advanced Combustion Engine Technologies
- Electrohydrodynamics and Fluid Dynamics
- Photovoltaic System Optimization Techniques
- Extracellular vesicles in disease
Guangxi University
2023-2025
Life Cycle Engineering (United States)
2025
Hebei University of Technology
2015-2024
University of Science and Technology of China
2023-2024
Baidu (China)
2024
Wenzhou Medical University
2024
Zhejiang Taizhou Hospital
2024
Zhejiang Cancer Hospital
2024
Huazhong Agricultural University
2023
Ministry of Agriculture and Rural Affairs
2023
Polylactic acid (PLA) has attracted much attention in bone tissue engineering due to its good biocompatibility and processability, but it still faces problems such as a slow degradation rate, acidic product, weak biomineralization ability, poor cell response, which limits wider application developing scaffolds. In this study, Mg(OH)2 nanoparticles were employed versatile nanofiller for PLA/Mg(OH)2 composite scaffolds using fused deposition modeling (FDM) 3D printing technology, mechanical,...
Caroli-de Gennes-Martricon (CdGM) states were predicted in 1964 as low energy excitations within vortex cores of type-II superconductors. In the quantum limit, namely $T/T_\mathrm{c} \ll \Delta/E_\mathrm{F}$, levels these to be discrete with basic at $E_\mu = \pm \mu \Delta^2/E_\mathrm{F}$ ($\mu 1/2$, $3/2$, $5/2$, ...). However, due small ratio $\Delta/E_\mathrm{F}$ most superconductors, it is very difficult observe CdGM states, but rather a symmetric peak appears zero-bias center. Here we...
This paper performs a comparative analysis to obtain the optimal cross-section shape and parameters of both pin fins vortex generators. A novel combined structure with generators is proposed enhance thermal performance an integrated microchannel heat sink. Effects nanoparticle diameter volume fraction are investigated using Al2O3 nanofluid DI-water as working fluid. Pin cause enhancements flow disturbance transfer on sinks. Results indicate that oval have better improvements...
To trace evolution of canine parvovirus-2 (CPV-2), a total 201 stool samples were collected from dogs with diarrhea in Heilongjiang province northeast China May 2014 to April 2015. The presence CPV-2 the was determined by PCR amplification VP2 gene (568 bp) CPV-2. results revealed that 95 (47.26%) positive for CPV-2, and they showed 98.8%–100% nucleotide identity 97.6%–100% amino acid identity. Of CPV-2-positive samples, types new2a (Ser297Ala), new2b 2c accounted 64.21%, 21.05%, 14.74%,...
Abstract Developing an intracellular delivery system is of key importance in the expansion protein-based therapeutics acting on cytosolic or nuclear targets. Recently, extracellular vesicles (EVs) have been exploited as next-generation modalities due to their natural role intercellular communication and biocompatibility. However, fusion protein interest a scaffold represents widely used strategy for cargo enrichment EVs, which could compromise stability functionality cargo. Herein, we report...
In an effort to trace the evolution of porcine epidemic diarrhea virus (PEDV), S1 and ORF3 genes viruses identified in 41 pig farms from seven regions (North, Northeast, Northwest, Central, East, South West, South, respectively) China 2015 were sequenced analyzed. Sequence analysis revealed that 29 our study exhibited nucleotide homologies 98.2%-100% 96.6%-100%, respectively; these two low sequence similarities with classical CV777 strain early Chinese LZC. Phylogenetic indicated PEDV...
Measurements on resistivity and magnetic susceptibility have been carried out for Bi single crystals under pressures up to 10.5GPa. The temperature dependent shows a semimetallic behavior at ambient low (below about 1.6GPa). This is followed by an upturn of in region when the pressure increased, which explained as semiconductor behavior. feature gradually gets enhanced 2.52GPa. Then non-monotonic appears upon further increasing pressure, accompanied strong suppression upturn. Simultaneously,...
A fiber-optic Fabry-Perot (F-P) sensor, based on a pendulum structure, for simultaneous measurement of tilt angle and vibration acceleration was proposed, which also has high-tilt resolution. The real-time cavity lengths are absolutely measured using fast demodulation algorithm. is estimated from the mean value while derives alternating quantity them. series experiments conducted micro-tilt platform table to simulate change perturbation, respectively. experimental results show resolution...
Abstract The generation of cultured red blood cells (cRBCs) ex vivo represents a potentially unlimited source for RBC transfusion and other cell therapies. Human cRBCs can be generated from the terminal differentiation proliferating erythroblasts derived hematopoietic stem/progenitor or erythroid precursors in peripheral mononuclear cells. Efficient maturation into highly depend on replenishing human plasma, which exhibits variable potency across donors batches complicates consistent cRBC...
Abstract Polylactic acid (PLA) has been widely utilized in the development of bone scaffolds. However, it is still constrained by issues, such as limited mechanical strength, slow degradation rate, low bioactivity, and suboptimal cell responses. In this study, a natural bioceramic fiber—wollastonite fiber (WF)—was incorporated into PLA matrix, PLA/WF composite scaffolds were fabricated via fused modeling deposition (FDM) 3D printing. The results indicated that properties initially enhanced...