A5091422437- Acute Myeloid Leukemia Research
- Advanced Sensor and Energy Harvesting Materials
- Advancements in Battery Materials
- Particle Accelerators and Free-Electron Lasers
- Particle accelerators and beam dynamics
- Electron and X-Ray Spectroscopy Techniques
- Photocathodes and Microchannel Plates
- Gas Sensing Nanomaterials and Sensors
- Myeloproliferative Neoplasms: Diagnosis and Treatment
- Silicon Nanostructures and Photoluminescence
- Graphene research and applications
- Luminescence and Fluorescent Materials
- Nanopore and Nanochannel Transport Studies
- Solar Radiation and Photovoltaics
- Ion-surface interactions and analysis
- Power Transformer Diagnostics and Insulation
- Thin-Film Transistor Technologies
- Advanced DC-DC Converters
- Sarcoma Diagnosis and Treatment
- Advanced Chemical Sensor Technologies
- Advanced battery technologies research
- High-Voltage Power Transmission Systems
- Protein Degradation and Inhibitors
- Low-power high-performance VLSI design
- Multiple Myeloma Research and Treatments
Zhejiang University
2012-2024
First Affiliated Hospital Zhejiang University
2023-2024
Hefei University of Technology
2022
The Synergetic Innovation Center for Advanced Materials
2019
Nanjing University of Posts and Telecommunications
2019
Tianjin University of Technology
2018
Zhejiang Province Institute of Architectural Design and Research
2012
University of Maryland, College Park
2010
The skylight polarization pattern contains rich information for navigation, meteorological monitoring, and remote sensing. In this paper, we propose a high-similarity analytical model by considering the influence of solar altitude angle on neutral point position variations distribution polarized skylight. A novel function is built to determine relationship between elevation based large number measured data. experimental results show that proposed achieves higher similarity data compared with...
Dual-functional MnO<sub>2</sub> nanowire/CNT modified layers were prepared to inhibit the polysulfide shuttle effect utilizing their strong adsorption capability and high conductivity.
The electronic structure characteristics of Pt1-, Pt2-, Pt3- and Pd1-doped graphene were investigated by first-principles calculations based on density functional theory (the subscript represents the number dopant atoms). It is found that either Pt or Pd atom can improve conductivity graphene, while stability doping better than Pd. also improved increasing concentration. However, doped decreases with increase Pt1- Pt2-doped achieve a good compromise between electrical conductivity....
In this work, for the first time, we combine electronic printing technology, electrostatic spraying technology and new 3D structure of ZnO.The was prepared with a simple, low-cost massive method that not successfully applied before.The ZnO tetrapods/PET composite device exhibits an output open-circuit voltage ~20 V short-circuit current ~300nA under repeated hand pressing.It is demonstrated power from PENG can directly drive light-emitting diodes (LEDs) charge capacitor.But typical flexible...
In this work, a silicon nanopillar array was created with nanosphere lithography. SnO2 film deposited on nanostructure by magnetron sputtering to form an SnO2/silicon sensor. The humidity sensitivity, response time, and recovery time were all measured at room temperature (25 °C) UV or without irradiation. As result, the sensitivity properties improved enlarging specific surface area ordered nanopillars irradiating light. These results indicate that sensors have potential applications in...
A Single-Inductor Dual-Output (SIDO) buck converter with a novel quasi-sliding mode (SM) controller is presented in this paper. Instead of keeping as constant current, the free-wheeling current level can vary according to load condition extend range while maintaining high power efficiency and less cross regulation at same time. To verify feasibility proposed technique, SIDO two regulated output voltages, 1.8V 3.3V, designed fabricated HEJIAN 0.35 μm CMOS process. Simulation experiment...
Abstract The construction of power grid engineering is developing more and rapidly. In order to ensure the large-scale transmission transformation projects, in field equipment materials, it necessary eliminate special such as over-time service equipment, increase amount high-performance materials. research development materials should focus on specialization, standardization, serialization carry out innovative development, thereby improving efficiency, safety quality levels, completing...
Polarimetric imaging has been studied and applied to the problem of visibility restoration in various scenarios such as haze, mist underwater. Although studies have shown that under certain conditions, circular polarimetric advantages over linear imaging, however, for a complex environment containing both scattering medium object, performance is affected by many factors. In this paper, propagation polarized light theoretically analyzed, then simulation experiments different experimental...
7042 Background: AML1-MTG16 and FUS-ERG are two rare fusion genes in acute myeloid leukemia (AML). Their clinical characteristics factors influencing prognosis have been summarized a cohort of pediatric patients, but no systematic review is approached adult. Methods: We retrospectively analyzed the data adult AML patients with or genes, who were reported on Mitelman Database, PubMed China national knowledge infrastructure (CNKI) from 1988 to 2022 received treatment First Affiliated Hospital,...
Quantum efficiency (QE) of a photoemissive surface is lowered via sub-monolayer coating adsorbed alkali metal: we here measure QE cesium, potassium, and sodium on tungsten refine theoretical predictions using hard-sphere model to compare experiment. We identify variation the percent-monolayer coverage corresponding peak as affected by adsorbate covalent diameter substrate lattice constant.
Abstract The technical field of transformers discussed in the paper relates to production lead wires, especially a factory-made prefabricated transformer with new wire; its includes main body and wire connected transformer. wire, copper-aluminium terminal, heat shrinkable tube, composite insulator, grounding test ring, lightning arrester assembly, C-clamp are arranged order from one end other end. design type assembly can completely realize factory prefabrication manufacturing process is...
Abstract The cold crimping process of the lead wire vertical transformer clamp cable is a commonly used manufacturing method in current process. Its advantages are: clean, simple, reliable, and convenient, which satisfies needs high-voltage electrical products. However, due to diversity cross-sectional area, actual operation, it often necessary fill between terminal, there are many optional specifications for filling line, may easily inconsistent methods unclear standards. Aiming at kind...